Binks HP 6/60 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 43

Binks HP 6/60 Скачать руководство пользователя страница 8

8

Packings:

The lifetime and the maintenance rate of a pump depend crucially on the right packing. The pack-
ing for solvent and waterbased paint are different.

For the use of high viscosity or high corrosion materials we recommend high-strength packing.
Depending on the field of application there are different packings for solvent and waterbased ma-
terials.

Standard packing:

Upper packing:
Mixed standard packing (for solvent paint materials)

Part-no.: 0114-014477

Consisting of: PTFE/Leather packing

Standard packing (for waterborne paint materials)

Part-no.: 0114-018924

Consisting of: PTFE packing

Lower packing:
Mixed standard packing (for solvent paint materials)

Part-no.: 0114-014476

Consisting of: PTFE/Leather packing

Standard packing (for waterborne paint materials)

Part-no.: 0114-018925

Consisting of: PTFE packing

Packings for high-strength and corrosion materials:

Upper packing:
Mixed high-strength packing (for solvent paint materials) Part-no.: 0114-016289

Consisting of: PTFE(high-strength)/Leather packing

High-strength packing (for waterborne paint materials)

Part-no.: 0114-016287

Consisting of: PTFE(high-strength) packing

Lower packing:
Mixed high-strength packing (for solvent paint materials) Part-no.: 0114-016290

Consisting of: PTFE(high-strength)/Leather packing

High-strength packing (for waterborne paint materials)

Part-no.: 0114-016288

Consisting of: PTFE(high-strength) packing

Note:
To the high-strength packings graphite is added to the PTFE. This improves the lubrication quali-
ties. High strength packings are not recommended for bright finish paint. Graphite can change the
colour of the finish paint.

If you need special packings without graphite admixture please contact your dealer.

Our pumps are supplied fitted work-sided with mixed packing for the application of solvent paint.

«
...
6
7
8
9
10
...
»

Содержание HP 6/60












































Отзывы:

Нет отзывов