Binks Cub SL 7011 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 8

background image

Important regulatory note

Regulations in some areas prohibit the operation of HVLP spray guns above 10 psi nozzle atomizing
pressure. users subject to this regulation should not exceed 50 psi gun inlet pressure (see the air pressure
chart for various fluid materials on page 7). Some agencies require users to have a nozzle test gauge
available on site to verify gun operating pressures. we recommend that you use Nozzle Test Gauge (Part
No. 54-4150) shown below for accurate nozzle operating pressures.

test gauge accessory

54-4150

(gauge only: 59-299)

3/13 ©2013 Binks All rights reserved. Printed in u.S.A.

u.s.a./canada customer service
195 Internationale Blvd.

Glendale Heights, IL 60139

630-237-5000

Toll Free Customer Service

and Technical Support

800-992-4657
Toll Free Fax

888-246-5732

Binks sales and service: www.binks.com

warranty

This product is covered by Binks’ 1 year Limited warranty.

77-2734r-7 revisions: Trademark updates.

«
...
6
7
8

Содержание Cub SL 7011 Series









Отзывы:

Нет отзывов

Похожие инструкции для Cub SL 7011 Series

SPRAY SYSTEM HV 1900

Бренд: Earlex Страницы: 22

SPRAY STATION HV3500

Бренд: Earlex Страницы: 2

Бренд: Graco Страницы: 2

Бренд: T4W Страницы: 10

700W Mechanical

Бренд: AGP Страницы: 24

Бренд: zogics Страницы: 5

Reactor H-XP3 Elite

Бренд: Graco Страницы: 58

Бренд: BGS technic Страницы: 17

Бренд: DeVilbiss Страницы: 4

Бренд: DeVilbiss Страницы: 8

Бренд: Sienna Страницы: 8

Бренд: Norstar Страницы: 77

Бренд: Valvolmeccanica Страницы: 6

Бренд: Sagola Страницы: 64

Бренд: Ferm Страницы: 16

Бренд: Ferm Страницы: 24

Бренд: Parkside Страницы: 28

KH 3114 PAINT SPRAY GUN

Бренд: Parkside Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды