background image

EN

77-2875-R7.2  (6/2015)

2 / 8

Binks reserves the right to modify equipment specification without prior notice.

LOCK OUT / TAG-OUT

Failure to de-energize, disconnect, lock out and tag-out all power 

sources before performing equipment maintenance could cause 

serious injury or death. 

OPERATOR TRAINING

 

All personnel must be trained before operating finishing 

equipment.

EQUIPMENT MISUSE HAZARD

 

Equipment misuse can cause the equipment to rupture, 

malfunction, or start  unexpectedly and result in serious injury.

PROJECTILE HAZARD

You may be injured by venting liquids or gases that are released 

under pressure, or flying debris.

PINCH POINT HAZARD

 

Moving parts can crush and cut. Pinch points are basically any 

areas where there are moving parts.

INSPECT THE EQUIPMENT DAILY

 

Inspect the equipment for worn or broken parts on a daily basis. 

Do not operate the equipment if you are uncertain about its 

condition.

In this part sheet, the words 

WARNING

CAUTION

 and 

NOTE

 are used to 

emphasize important safety information as follows:

Hazards or unsafe practices which 

could result in minor personal injury, 

product or property damage.

!

 

CAUTION

Hazards or unsafe practices which 

could result in severe personal 

injury, death or substantial property 

damage.

!

 WARNING

Important installation, operation or 

maintenance information.

NOTE

Read the following warnings before using this equipment.

READ THE MANUAL

 

Before operating finishing equipment, read and understand all 

safety, operation and maintenance information provided in the 

operation manual.

WEAR SAFETY GLASSES

 

Failure to wear safety glasses with side shields could result in 

serious eye injury or blindness.

NEVER MODIFY THE EQUIPMENT

 

Do not modify the equipment unless the manufacturer provides 

written approval.

IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT.

FOR FURTHER SAFETY INFORMATION REGARDING THIS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300).

KNOW WHERE AND HOW TO SHUT OFF THE EQUIPMENT 

IN CASE OF AN EMERGENCY

PRESSURE RELIEF PROCEDURE 

Always follow the pressure relief procedure in the equipment 

instruction manual.

NOISE HAZARD

 

You may be injured by loud noise. Hearing protection may be 

required when using this equipment.

STATIC CHARGE

 

Fluid may develop a static charge that must be dissipated through 

proper grounding of the equipment, objects to be sprayed and all 

other electrically conductive objects in the dispensing area. Improper 

grounding or sparks can cause a hazardous condition and result in 

fire, explosion or electric shock and other serious injury.

PROP 65 WARNING

WARNING: This product contains chemicals known to the  

State of California to cause cancer and birth defects or other 

reproductive harm.

WEAR RESPIRATOR

 

 Toxic fumes can cause serious injury or death if inhaled.  

Wear a respirator as recommended by the fluid and solvent 

manufacturer’s Material Safety Data Sheet.

TOXIC FLUID & FUMES

 

 Hazardous fluid or toxic fumes can cause serious injury or death if 

splashed in the eyes or on the skin, inhaled, injected or 

swallowed. LEARN and KNOW the specific hazards or the fluids 

you are using.

KEEP EQUIPMENT GUARDS IN PLACE

 

Do not operate the equipment if the safety devices have been 

removed.

!

 WARNING

AUTOMATIC EQUIPMENT

Automatic equipment may start suddenly without warning. 

FIRE AND EXPLOSION HAZARD

 

Improper equipment grounding, poor ventilation, open flame or 

sparks can cause a hazardous condition and result in fire or 

explosion and serious injury.

MEDICAL ALERT

 

Any injury caused by high pressure liquid can be serious. If you 

are injured or even suspect an injury:

•  Go to an emergency room immediately.
•  Tell the doctor you suspect an injection injury.
•  Show the doctor this medical information or the medical alert 

card provided with your  airless spray equipment.

•  Tell the doctor what kind of fluid you were spraying or 

dispensing.

GET IMMEDIATE MEDICAL ATTENTION

 

To prevent contact with the fluid, please note the following:

•  Never point the gun/valve at anyone or any part of the body.
•  Never put hand or fingers over the spray tip.
•  Never attempt to stop or deflect fluid leaks with your hand, 

body, glove or rag.

•  Always have the tip guard on the spray gun before spraying.
•  Always ensure that the gun trigger safety operates before 

spraying.

Содержание 7042-6931-4









Отзывы: