Binks 41-818836 Скачать руководство пользователя страница 8

Страница: 8 / 22

B41-818836conductiveacetal-rev0416

Model 41-818836 Conductive Acetal Ball Valve Pump Page 6

Recycling

Many components of Conductive

Acetal AODD pumps are made of

recyclable materials (see chart on

page 10 for material specifications).

We encourage pump users to recycle

worn out parts and pumps whenever

possible, after any hazardous pumped

fluids are thoroughly flushed.

This pump is pressurized

internally with air pressure

during operation. Always

make certain that all bolting

is in good condition and

that all of the correct

bolting is reinstalled during assembly.

WARNING

Before pump operation,

i n s p e c t a l l g a s k e t e d

fasteners for looseness

caused by gasket creep. Re-

torque loose fasteners to

prevent leakage. Follow recommended torques

stated in this manual.

CAUTION

When used for toxic or

aggressive fluids, the pump

should always be flushed

clean prior to disassembly.

WARNING

Before maintenance or

repair, shut off the com-

pressed air line, bleed the

pressure, and disconnect

the air line from the pump.

The discharge line may be

pressurized and must be bled of its pressure.

WARNING

IMPORTANT

Read these safety warnings

and instructions in this

manual completely, before

installation and start-up

of the pump. It is the

responsibility of the purchaser to retain this

manual for reference. Failure to comply with

the recommendations stated in this manual will

damage the pump, and void factory warranty.

WARNING

Airborne particles and loud

noise hazards.
Wear ear and eye protection.

B e f o r e d o i n g a n y

maintenance on the pump,

be certain all pressure is

completely vented from the

pump, suction, discharge,

piping, and all other openings and connections.

Be certain the air supply is locked out or made

non-operational, so that it cannot be started

while work is being done on the pump. Be

certain that approved eye protection and

protective clothing are worn all times in the

vicinity of the pump. Failure to follow these

recommendations may result in serious injury

or death.

WARNING

In the event of diaphragm

rupture, pumped material

may enter the air end of the

pump, and be discharged

into the atmosphere. If

pumping a product which is hazardous or toxic,

the air exhaust must be piped to an appropriate

area for safe disposition.

Important Safety

Information

Take action to prevent static

sparking. Fire or explosion

can result, especially when

handling flammable liquids.

The pump, piping, valves,

containers or other miscellaneous equipment

must be grounded. (See Page 20)

WARNING

Содержание 41-818836























Результаты поиска

Содержание 41-818836

Отзывы:

Похожие инструкции для 41-818836

Бренды по названию

Популярные бренды

Binks 41-818836, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 41-818836

Отзывы:

Похожие инструкции для 41-818836

Бренды по названию

Популярные бренды