Binder COMBIMASS compact Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 53

Binder COMBIMASS compact Скачать руководство пользователя страница 7

COMBIMASS

®

compact

Doc. No.: 0905EE20500

7

Chapter 1 Safety, General Information

Chapter 1 Safety, General Information

SYMBOLS

This Assembly and Operating Manual highlights safety information as follows:

The danger information directs the attention of the operator towards a special procedure or practice which
can cause serious injury to persons if carried out incorrectly.

The information warning the user against certain procedures indicates that failure to observe this informa-
tion can cause serious damage to the equipment.

The notes highlight important information in the text.

SAFETY PRECAUTIONS

This document describes general safety precautions for handling units of the COMBIMASS

®

series with

regard to installation, operation and maintenance.
This document is intended as additional information and not as a substitute for the specific safety regula-
tions of the country of destination. Compliance with the safety regulations is the responsibility of the cu-
stomer, the user and/or the expert personnel involved.
Before using COMBIMASS

®

products, please observe the relevant documentation. Please also note the

safety information given in this chapter and in the operating manuals.
Before using the unit, the user should read this operating manual carefully. BINDER GmbH will accept no
responsibility for complete or partial failure to comply with the information included in the manual, incor-
rect use by untrained personnel, unauthorized manipulation and any use which does not comply with the
national regulations. During installation, setup and maintenance work, all instructions included in this ope-
rating manual must be complied with.
The measuring system with a stainless steel sensor tube and a stainless steel sensor (standard version) is
suitable for the mass flow measurement of gases.
It is not suitable for measuring flowing liquids.

Please note:

The maintenance measures described in this manual must be carried out by experpert
personnel only.

DANGER

ATTENTION!

NOTE

DANGER

«
...
5
6
7
8
9
...
»

Содержание COMBIMASS compact






















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды