Binder 9010-0269 Скачать руководство пользователя страница 11

Страница: 11 / 69

FDL (E2) 03/2011

page 11/68

1.2.4 Word message panel structure

Type / cause of hazard.

Possible consequences.

∅

Instruction how to avoid the hazard: prohibition

Instruction how to avoid the hazard: mandatory action

Observe all other notes and information not necessarily emphasized in the same way, in order to avoid
disruptions that could result in direct or indirect injury or property damage.

1.3

Localization / position of safety labels on the unit

The following labels are located on the unit:

Pictograms (Warning signs)

Service label

Hot surface

Figure 1: Position of labels on the unit

Keep safety labels complete and legible.

Replace safety labels that are no longer legible. Contact BINDER Service for these replacements.

Содержание 9010-0269






































































Результаты поиска

Содержание 9010-0269

Отзывы:

Похожие инструкции для 9010-0269

Бренды по названию

Популярные бренды

Binder 9010-0269, Руководство по эксплуатации

Результаты поиска

Содержание 9010-0269

Отзывы:

Похожие инструкции для 9010-0269

Бренды по названию

Популярные бренды