10
6.7. Output Connections
The B-500-MTRX-230 matrix switcher is equipped with one HDMI and one HDBaseT output port for each of the
16 output zones. See the sections below for specific instructions and details for each connection type.
Note:
Any input selected on an output zone is played on both the HDMI and HDBaseT outputs for that zone
simultaneously. This can be used to feed the same source to two devices. Read more about this feature below.
6.8. Choosing the Correct Output Connection
• Outputs to sinks (TVs, AV receivers, etc.) can be connected using either an HDMI cable or a Category cable
along with an HDBaseT Receiver (with a short HDMI cable).
• Use HDBaseT for any run over about 50 feet or for any output that will utilize IR passthrough.
• Use HDMI for short runs where IR passthrough is NOT needed.
•
In some situations it may be beneficial to use both outputs. If two displays need to be fed the same source at all
times, one display can be fed from the HDBaseT output, and one from the HDMI output.
Example:
In a setup where an AV receiver feeding surround sound to a zone, the audio can be fed to the receiver
via HDMI, and an HDBaseT receiver can be used to route video to the display. This is beneficial with AV receivers
that have older or less reliable HDMI scaling or passthrough.
6.9. HDMI Outputs
The HDMI outputs of the Matrix can be connected to the input of a sink device (TV, AV receiver, fiber extender,
etc.). Please follow the guidelines below to ensure best performance and reliability.
• Always use the shortest, possible cable between equipment. Use high speed rated cables to guarantee the best
possible performance.
• Always run continuous HDMI cables and avoid using HDMI cable adapters.
• When routing HDMI to an AV receiver, make sure to set the AV receiver to an HDMI mode where the signal
will not be processed or scaled to a different format. This will avoid signal timing issues that can cause
intermittent sync or total loss of sync. Contact the device manufacturer for details regarding HDMI setup.
6.10. HDBaseT Outputs
Follow the guidelines outlined below when selecting and installing the HDBaseT cable.
6.11. HDBaseT Wiring Recommendations
Cable Type- Shielded or Unshielded Cat
• Cable Distance Limitations:
Cat 5e/6:
Up to 200 ft
Cat 6a/7:
Up to 230 ft
• Use the shortest possible length of high-quality twisted pair solid conductor Category cable rated to at least
350 Mhz bandwidth. The higher the cable standard, the better it will perform.
• For best results, install shielded cable with grounded shield drains. This reduces signal dropouts and artifacts
caused by electromagnetic and radio interference (EMI/RFI) from ceiling fans, appliances, electric motors, etc.
• Up to two patch cables can be used provided that they are not longer than 5m in length, and 568B terminated.
Use shielded patch cables if the run is shielded to maintain shield continuity.
• Use no more than two keystones or couplers in the run. Use shielded keystones or couplers with shielded cable
to maintain continuity.
• Cleanly terminate all cable ends and test every cable used before connecting the extender to avoid having to
troubleshoot termination problems later.
• Mark each end of the HDBaseT cable with the included labels to avoid confusion.
Connector Type- RJ45
• Use a high quality RJ45 connector that matches or exceeds the standard of the cable in use. Shielded
connectors must be used with shielded cables, and must maintain continuity of the shield to both connectors
to protect from interference.
• The use of
EZ
style, open end RJ45’s with HDMI extenders is discouraged.
• Always terminate RJ45 connectors in the HDBaseT signal path to the 568B termination standard as required
by HDBaseT standards.
Содержание B-500-MTRX-230-16x16
Страница 32: ...16 2 Rev 151130 0840...
