Bimba Intellipress Скачать руководство пользователя

Страница: 17 / 18

INTELLIPRESS

™

ELECTRIC BENCH TOP PRESS

User Manual

BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622

See Figure 13: Operator Run Screen

This section will explain how to interpret the Press Status messages, reset the Run Count, and troubleshoot
the press in the event of an error/fault. For this section, refer to the Operator Run Screen (Figure 13).

SECTION 4: PRESS STATUS, RUN COUNT, AND ERROR RESET

The press has three status indications:

•

Ready

- A bold

READY

signal indicates the press is ready for the next input.

Any input to the press (Home Position, Start Signal, Stop, E-Stop, etc.) will be executed.

•

Running

- A bold

RUNNING

signal indicates the press is currently performing an operation.

Any additional input to the press while the press is in a RUNNING state other than the Stop icon

will cause fault to the press.

•

E-STOP

- A bold

E-STOP

signal indicates the E-Stop button has been depressed.

The press will not function until the E-STOP button has been reset.

SECTION 4.1: STATUS

SECTION 4.2: RUN COUNT

•

The

RUN COUNT

status keeps a running total of how many times the start signal has been energized.

The

RUN COUNT

can be reset by pressing the RESET RUN COUNT button.

SECTION 4.3: ERROR RESET

To recover from any error, follow the following steps:

•

If displayed, close the red Alarm error screen by selecting the red “X” in the upper right-hand corner of

the Alarm section.

Press the

STOP

icon.

Press the

ERROR RESET

button.

Press the

Home Position

button.

•

If the press still fails to return to the Home Position then please follow these instructions:

Press the

Error Reset

button again.

Press the

Home Position

button.

Содержание Intellipress



















Результаты поиска

Содержание Intellipress

Отзывы:

Похожие инструкции для Intellipress

Бренды по названию

Популярные бренды

Bimba Intellipress, Руководство пользователя

Результаты поиска

Содержание Intellipress

Отзывы:

Похожие инструкции для Intellipress

Бренды по названию

Популярные бренды