Part No. 790161 Form No. F032399A
Page 12 of 12
Solution
Problem
Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Engine Service and Warranty
Will not vacuum or has poor
vacuum performance.
Adjust nozzle position. Unclog hose or exhaust (see page 6).
Allow air to feed with debris.
Nozzle height too high or too low. Clogged hose or exhaust. Excessive
quantity of debris.
- Throttle stop switch in idle position.
- Out of gasoline. Bad or old gasoline.
- Spark Plug wire disconnected.
- Dirty air cleaner.
Abnormal vibration.
Check impeller and replace if required. Check Engine.
- Check throttle.
- Check gasoline, Replace if gasoline is old.
- Connect spark plug wire.
- Clean or replace air cleaner. Or contact a qualified service person.
Loose or out of balance impeller or loose engine.
Engine is locked, will not
turn over.
Debris locked inside impeller. Engine problem.
See page 6, Clearing a clogged impeller housing. Contact an engine
servicing dealer for engine problems.
Parts List
continued from
page 11.
* Denotes standard
hardware item that may
be purchased locally.
Purchased
from
Purchase
Date
Serial Plate
R
ecord your machine model, serial number and
date-of-purchase and where purchased
R
min
-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model
Serial No.
Unit(Weight)
Engine Power
lbs.
kg
kW
rpm
89
L
A
L
A
p
94
Engine will not start.
(starter does not turn)
Engine will not start.
(starter turns)
- Charge battery or replace if the battery does not hold charge.
- Clean battery terminal and cable then reconnect.
- Install hose coupler securely to the unit and check whether
interlock switch is engaged by lever.
- Check harness wire connection and replace if necessary.
- Battery is low or dead.
- Battery cable is disconnected or battery terminal is corroded.
- Hose coupler is not installed, allowing interlock switch to operate.
- Harness wire is bad or disconnected from interlock switch.
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 WEBSITE: www.billygoat.com
BRIGGS & STRATTON PART NUMBERS. AVAILABLE THROUGH BRIGGS & STRATTON SERVICING DEALERS
Contact your nearest engine manufacturer's authorized
servicing dealer.
63
*81710 03
W A SHER 5 /16 FLA T CUT
22
64
*81710 04
W A SHER FLA T 3/8
2
65
*81720 07
W A SHER 1 /4 SA E
2
66
*81720 08
W A SHER 5 /16 SA E
2
67
*92011 25
KEY 1/4 x 2 3/4
1
68
*81720 20
W A SHER 5 /16 FENDER
4
69
790 163
DOOR FLA PPER INTA KE QL W A
1
70
790 230
BRA CKET BA TTERY QL
1
71
790 231
ROD BA TTERY HOLD DOW N
2
72
790 232
LA BEL W A RNING SECURE
3
73
790 125- S
HOUSING A SSY QL ( INCLUDES 1 8,49 ,50 ,72 )
1
74
430 208
SHEET META L SCREW 1/4 x 3/4 DRILL POINT
2
75
790 138- 01
GUA RD MUFFLER GUA RD
1
76
790 138- 02
GUA RD MUFFLER GUA RD BOTTOM
1
77
830 276
LA BEL ON / OFF
1
78
790 228
BRA CKET W HEEL QL
2
79
790 240
90 DEGREE ELBOW 1/8" NPT MA LE X 1/4"
1
80
*80410 26
SCREW CA P 5/16- 18 X 3/4 HCS Z P
4
81
790 258
CA P TA NK FUEL 3 GA L
1
82
790 257
TA NK FUEL 3 GA L
1
83
790 100- 04
IGNITION SW ITCH
1
84
850 443
W A SHER PLA TE IMPELLER
1
85
804 1008
SCREW CA P 1/4- 20 x 1 1/2
1
86
500 267
GRIP HA NDLE 1" x 7.5"
1
87
88
89
790 254
PLA TE CLA MP SPLIT
2
90
790 253
PLA TE CLA MP SPA CER
1
91
790 252
PLA TE CLA MP HA LF
4
92
816 3002
LOCK NUT 5/1 6-1 8 THIN Z P
8
93
802 4040
BOLT CA RRIA GE 5/16- 1" Z P
6
