background image

382514_B_HI

3

Specifications

Engine:

 B&S VANGUARD 6.5HP w/6:1

Engine Model No. 

12V3520006F1

Engine Fuel Capacity

3.7 qt. (3.1 L)

Engine Oil Capacity

0.63 qt. (0.59 L)

Total Unit Weight

242 lb (109.8 kg)

Length

57” (1.45 m)

Width

24”( .61 m)

Height

40” (1 m)

Maximum Operating Slope

15

o

Intended Use

PL1802V

AERATOR

This machine is designed for aerating established lawns and large grass covered areas. The machine should 

not be used for any other purpose than that stated above.

DO NOT OPERATE IF EXCESSIVE VIBRATION OCCURS! 

If excessive vibration occurs, shut engine off immediately and check for damaged or worn reel, loose reel 

bearing, loose engine or lodged debris. To remove debris from the machine, see the machine specific trouble 

shooting section. Note: See parts list for proper bolt torque specifications. 

HANDLING & TRANSPORTING

Always use two or more people to lift these machines. Lift holding on either side of the machine, using the han

-

dles and the frame. Secure in place during transportation. See specifications for unit weight.

For safety, use gloves when lifting.

Never lift any machine while the engine is running.

NOT 

FOR 

REPRODUCTION

Содержание PL1802V


































Отзывы: