Billy Goat PL1801 Скачать руководство пользователя

Страница: 18 / 33

Part No. 382510

382510_B_HI

Troubleshooting

Problem

Possible Cause of Problem

Possible Solution to Problem

Engine will not start.

• Stop switch is in OFF position.

• Throttle is in OFF position.

• Engine is not in full choke

position.

• No gasoline in engine.

• Gasoline in engine has expired.

• Oil level in engine is too low.

• Air filter is dirty.

• Check stop switch, throttle, and

choke positions.

• Check engine’s gasoline level

and quality.

• Check engine’s oil level and

quality.

• Clean or replace air filer.

• Contact a qualified engine

servicer.

Machine vibrates abnormally.

• Tines are damaged or missing.

• Handle bolts are loosened.

• Engine bolts are loosened.

• Stop work immediately!

• Replace damaged or missing

tines.

• Tighten all loose nuts and bolts.

Engine stalls or labors when

aerating.

• Slope is too steep for operation.

• Engine oil level is too low.

• Work at a 45

angle to the slope.

• Work up and down the slope, not

across.

• Check engine oil level and add oil

when appropriate.

Engine is locked and will not pull

over.

• Debris is locked against drive

pulleys.

• Engine is malfunctioning.

• Pull spark plug wire.

• Remove debris from drive

pulleys.

• Contact a qualified engine

servicer.

Machine does not move when the

clutch is engaged.

• Drive belt is out of adjustment.

• Drive belt is worn.

• Pulleys are loose or damaged.

• Clutch cable is damaged or

broken.

• Refer to subsection “Replacing

the Drive Belt” in the Maintenance

section of this manual to perform

the belt replacement properly.

• Contact a qualified engine

servicer.

NOT

FOR

REPRODUCTION

Содержание PL1801


































Результаты поиска

Содержание PL1801

Отзывы:

Похожие инструкции для PL1801

Бренды по названию

Популярные бренды

Billy Goat PL1801, Руководство пользователя

Результаты поиска

Содержание PL1801

Отзывы:

Похожие инструкции для PL1801

Бренды по названию

Популярные бренды