Billy Goat MV600SPE страница 19 Скачать руководство пользователя

Страница: 19 / 27

Form No F050112D

Part No 840245

MV650SPH Self-

Propelled Vacuum Owner’s Manual

TROUBLESHOOTING

Problem

Possible Cause

Solution

Will not vacuum or has poor vacuum
performance.

· Dirty or full debris bag or filter.

· Clean debris bag and filter. Shake bag clean or
wash.

· Nozzle height set too high or too low.

· Adjust nozzle height (see page 14).

· Hose kit cap missing.

· Check for hose kit cap.

· Clogged nozzle or exhaust.

· Unclog nozzle or exhaust (see page 5)

· Excessive quantity of debris.

· Allow air to feed with debris.

Abnormal vibration.

· Loose or out of balance impeller.

· Check impeller and replace if required.

· Loose engine.

· Check engine.

Engine will not start.

· Throttle in off position.

· Check throttle control (see page 13).

· Engine not in full choke position.

· Check throttle, choke position (see page 13).

· Out of gasoline or bad, old gasoline.

· Check gasoline.

· Spark Plug wire disconnected.

· Connect spark plug wire.

· Gas valve off.

· Turn on gas valve.

· Dirty air cleaner.

· Clean or replace air cleaner. Contact a qualified
service person.

· Safety Interlock disengaged on bag plate.

· Latch the bag properly or check the bag rod to
see if it is bent.

Engine is locked, will not pull over.

· Impeller plugged or clogged.

· Remove debris (see page 16).

· Engine problem.

· Contact an engine servicing dealer for engine
problems.

No self-propelling

· Drive clutch not engaged

· Engage the drive clutch lever.

· Transmission not in gear.

· Check transmission shift control (see page 16).

· Drive belt worn or broken

· Check the drive belt.

· Drive clutch cable out of adjustment or broken. · Check the drive clutch cable (see page 20).

· Spring tension too loose

· Check spring legnth (see page 20).

· Drive chain off the sprocket.

· Check the drive chain (see page 22).

Self propelled drive will not release

· Improper drive clutch cable adjustment or
cable is kinked.

· Check the drive clutch cable (see page 20).

Noisy or broken chain

· No chain lubrication.

· Lubricate chain.

· Chain misalignment or tension.

· Check the drive chain (see page 22).

Содержание MV600SPE




























Результаты поиска

Содержание MV600SPE

Отзывы:

Похожие инструкции для MV600SPE

Бренды по названию

Популярные бренды

Billy Goat MV600SPE, Руководство пользователя

Результаты поиска

Содержание MV600SPE

Отзывы:

Похожие инструкции для MV600SPE

Бренды по названию

Популярные бренды