Big Joe EZ30 Скачать руководство пользователя

Страница: 22 / 134

4-2

BL-EZ30-0815 - 07-28-2019

Table 4-1 Troubleshooting Chart - Continued

MALFUNCTION

PROBABLE CAUSE

CORRECTIVE ACTION

TROUBLE WITH BRAKING -

Continued

Brake drags.

Defective electric brake.

Replace.

Brake grabs.

Defective electric brake.

Replace.

Abnormal noise and chatter when

brake is applied.

Defective electric brake.

Replace.

TROUBLE WITH LIFTING OR

LOWERING

Oil sprays or flows from the top of

the lift cylinder.

Defective packing in lift cylinder

Repair lift cylinder.

Squealing sounds when lifting

forks.

a. Oil level too low.

Identify oil leak.

b. Lift linkage binding.

Apply grease.

Forks do not lift to top.

Oil level too low.

Add oil to reservoir.

Weak, slow or uneven action of

hydraulic system.

a. Defective pump or relief valve.

Check pressure. Adjust as

necessary.

b. Worn lift cylinder.

Replace cylinder.

c. Load larger than capacity.

Refer to I.D.plate for capacity.

d. Defective lift motor solenoid.

Replace solenoid on electrical

panel.

e. Battery charge low.

Charge battery.

Forks do not lift, pump motor does

not run.

a. Battery is dead or discon-

nected.

Check and recharge if required.

b. Defective wiring.

Check and repair as required.

c. Defect in electrical system for

operating pump motor.

Check lift switch in control head,

as well as the solenoid.

Forks do not lift, motor runs.

Defect in hydraulic system.

Check the oil level in the reservoir

and the oil lines to the lift cylin-
der, and repair as required. If
normal, check the hydraulic
pump, and relief valve. Repair,
or adjust.

Содержание EZ30







































































































































Результаты поиска

Содержание EZ30

Отзывы:

Похожие инструкции для EZ30

Бренды по названию

Популярные бренды

Big Joe EZ30, Эксплуатация, техническое обслуживание, список запасных частей

Результаты поиска

Содержание EZ30

Отзывы:

Похожие инструкции для EZ30

Бренды по названию

Популярные бренды