background image

 

Translation of the original operating manual 

Drive unit for flexible shafts 

– MB 50 

 

 

OI NO.: 001 580 674                  

- 3 - of -16- 

Version 16.01.2020 

 

GB 

The proprietor must ensure that operators have read and understood the operating manual before they use the 
unit. 

The proprietor must ensure that unauthorised persons are denied access to the unit. 

In-house health and safety regulations must be observed. 

3  Intended Use 

The drive unit for flexible shafts is used to mount and drive flexible shafts and tools for 

 

grinding 

 

milling 

 

deburring 

 

polishing and 

 

brushing 

different materials. 

You must make sure that only BIAX products are connected to the drive unit. 

The drive unit must not be operated in rooms with explosive or combustible gases, or gases hazardous to health. 

 

Any use of the drive unit for flexible shafts beyond the area of application stipulated, or constructional modifications 
to it, are not permitted without prior agreement from Schmid & Wezel. Liability for any consequential damage is 
annulled in the case of non-compliance. 

4  Safety 

4.1  Safety Labels 

The following key words are used in conjunction with the safety labels throughout this document to indicate 
potential hazards 

 

 

DANGER 

High risk of fatal or severe injury and considerable property damage if the 
corresponding safety precautions are not taken! 

 

WARNING 

Risk of fatal or severe injury and considerable property damage if the corresponding 
safety precautions are not taken! 

 

CAUTION 

Risk of minor injury if the corresponding safety precautions are not taken! 

 

ATTENTION 

Risk of damage to property if the corresponding safety precautions are not taken! 

4.2  General Safety Precautions 

 

WARNING 

Read all safety instructions, instructions, pictures and technical data provided with 
this power tool. 

Failure to follow the instructions below can result in electric shock, fire 

and/or serious injury.

 

 

Keep all safety instructions and instructions for future reference. 

Содержание MB 50

















Отзывы: