BH Hipower SK LINE H800Tv, Инструкция по сборке и эксплуатации, Страница: 9 / 32

SK
LINE
sportkoncept
9
1.
ASSEMBLY INSTRUCTIONS.-
Take the unit out of its box and make sure that all
of the pieces are there, Fig.1:
(56) Main post with handlebar; (1) Main body; (40)
Front trim cover; (34) Top trim cover; (36) Rear
trim cover; (115) Bottle holder; (28) Flat washer M-
10; (95) Grower washer M-10; (99) Allen screw M-
10x25; (112) Screw M-4x15; (43) Self-tapping
screw 4x20; (104) Allen key; (120) Star-driver
spanner;(X01) The adapter. H800TV 15v. 2Amp.
2.
FITTING THE MAIN POST.-
Take hold of the post (56) and bring it up to the
boss on the main body (1), connect the terminals
(H82; H84; H83; H17), sticking out of the bottom of
the post, with terminal (L04; L06; 26) coming up
out of the top of the tube on the main body (1),
Fig.2, now slip the main post over the boss on the
main body in the direction of the arrow, making
sure not to snag any of the cables.
Check that the cables are connected correctly by
spinning the dynamo until the monitor starts to
operate.
Once you have checked that it works, insert
screws (99) along with their flat washers (28) and
Grower washer (95) Fig.2.
Line the main post up with the main body and
tighten the screws securely.
3.
FITTING THE FRONT TRIM COVER.-
Fit the trim cover by sliding it onto the side tubes,
see Fig.3. Next, take screw (112) and secure the
cover by tightening the screw.
Next, remove the screws (116), from the main post
(56), Fig.3, position the bottle holder and secure it
by using the screws removed previously.
4.
FITTING THE TOP TRIM COVER.-
Position the trim cover on top of the side tubes,
see Fig.4, slide the cover forward, inserting it into
the slots on the main body (1) then position it on
the saddle post in the direction of the arrow.
5.
FITTING THE REAR TRIM COVER.-
Having completed the previous steps, take the rear
cover (36) and position it on the saddle post, as
shown in the direction of the arrow Fig.5., and
screw it to the top trim cover and the saddle post
using screws (118).
6
. ADJUSTING THE SADDLE HEIGHT.-
Loosen the saddle height control knob (19) a little,
Fig.6, turning it anti-clockwise and then pulling the
saddle upward, when it is at the right height lock it
into position by turning the height control knob (19)
clockwise until secure.
7
. LEVELLING.-
Once the unit has been placed into its final position
for doing exercise, make sure that it sits flat on the
floor and that it is level. This can be achieved by
screwing the adjustable support blocks (92) up or
down, as shown in Fig.7.
8
. MOVEMENT & STORAGE.-
The appliance is equipped with wheels (97) making
it easier to move about. The two wheels at the front
of the appliance make it easy to store the machine
away, as shown in Fig.8.
9.
PULSE MEASUREMENT.-
Your pulse rate is measured by placing both hands
on pulse sensors (110) located on the seat
handgrips or the handlebar, see Fig.9.
NOTE:
You can also use the chest band (OPTIONAL
TELEMETRIC PULSE SENSOR) to measure your
heart rate.
The reading from the telemetric pulse rate takes
preference over the pulse sensors (110) located on
the seat handgrips or handlebar.
10
. BATTERY CHARGE.-
Before starting the battery charge, make sure that
the mains voltage is compatible with the AC/DC
adaptor.
Connect the AC/DC adaptor (X01) to the mains.
Then, connect the DC terminal to the connector
located at the low end of the chain cover Fig.10.
BH RESERVES THE RIGHT TO MODIFY
THE SPECIFICATIONS OF ITS
PRODUCTS WITHOUT PRIOR NOTICE.