44
28.-
Now take the weight selector tube
(44), Fig.23, and attach the holding
collar (46) for the first weight and
insert the lockpin (45). Fit the last
weight (43) onto the bars (38).
Fit the bushes (69) tighten the bolts
(106) for the guide post (38) to the
main body (5), as shown in Fig.23.
FITTING THE CABLE SYSTEM.-
29.-
First check that the steel cables
are correctly fitted into the pulleys that
are supplied prefitted, following the
arrows in Fig.13.
The weights have already been
fitted into their housing in the previous
assembly step.
Lift the first weight (42) and fit the
weight selector post (39), as shown in
Fig.24A.
Screw bolt (63) into the selector
post (39), when it is screwed in, lower
the weight so that it rests on the other
weights.
Insert the weight selector pin (44)
into the selector post (39), Fig.23, and
tighten nut (U) securely, Fig.24A.
Next, attach one end of cable (65)
to the left arm plate for the Butterfly
exercise, Fig.24B, fit bolt (103) with
washers (119) and nut (125).
Do the same with the other end of
cable (65) for the right Butterfly
exercise arm.
Fit the plates (59) onto the pulleys
(56) as shownh in Fig.24C.
Take the end of the foot pull-up
cable (64) and by following the arrows
marked on the cable, Fig.24, pass it
through the first pulley (A1), as shown
in Fig.24.
Next, pass the same tip through
lower pulley (B1; C1) Fig.24.
Continue passing the tip of the
cable (64) through the third pulley (D1)
Fig.24. Attach the end of the cable to
the carabiner (60) and to chain (61),
position it on the end joined to the
support on the base, Fig.24.
Note:
After a while you may notice
that steel cable slackens a little due to
the cable settling into position.
To remedy this just tension the steel
cable by changing the chain link (61).
30
.- Fit the chain (62) onto the leg
accessory hook (41) Fig.24, to be able
to do the leg exercises.
31.-
Attach the top casing (127) fitting
it over the upper body (1) so that it
slots onto the main body (5) Fig.25.
Fasten on using screws (97).
32.-
Set the selector (70) as shown in
Fig.25 to be able to do the Butterfly
exercise.
REAR PROTECTION ASSEMBLY.-
32A
.-Place the fixing points (133) in
the mesh (134) as shown in Fig.25A.
Then, position the fixing points (133)
on the main body (5), place the
screws (98), with washers (118) and
tighten, as shown in Fig.25A.
POSITIONING THE WEIGHT
SEECTOR ROD.-
33.-
Insert the weight selector (44) rod
into the orifice of the weights required
for the exercise, as shown in Fig.26.
34.-
When the rod notch has been fed
through the weight selector tube (39),
turn the selector rod anticlockwise, so
that the rod is held into place as
shown in Fig.27. Check that the
selector is firmly in position and that it
does not protrude from the weight
selector. To remove the rod, turn it
clockwise and pull.
Содержание GlobalGym plus G152X
