background image

7

Strictly perform installation, set-up, maintenance, cleaning 

and transportation with the unit switched off and all moving 

parts firmly secured against accidental operation. Immedia-

tely disconnect power off the machine in case of any eventual 

faults or troubles.

The user shall strictly comply with these operation, set-up, mainte-

nance, repair and trouble-shooting instructions in order to assure 

safe operation and avoid damages to the equipment. The owner must 

understand these instructions and must allow only persons who un-

derstand these instructions and are familiar with the related risks to 

operate the loader. Moreover we recommend to let the machine be 

run only and strictly by trained and skilled staff who must be familiar 

with the applicable occupational safety and health administration rules 

as well as applicable transportation rules. Incorrect use of the splitter 

can cause serious injury or death.

 

No person under school leaving age (18) should operate this log split-

ter. Those who have reached school leaving age but are below the age 

of 16 may operate a log splitter if supervised by a competent person 

of 18 years or over. The machine shall be installed and kept in a sui-

table location selected by the customer for safest operation. 

Make sure that the equipment stands on a safe stable foundation.

 

Do not allow within the hazardous zone any unauthorized third or per-

sons who are not familiar with the dangers related to use and opera-

tion of the machine. Allow no bystanders, especially children and pets 

in the working area.

• Log loaders are not designed for passengers transportation.

• Strictly control/operate the log grapples from the  

  driver‘s seat on the tractor.

Do not allow any thirds in the dangerous zone.

The dangerous zone  includes the swivel/rotation area as well as the 

bucket and grapples operation (grasp/release) area.  

Provide due clearance around the log/timber handling zone. 

• Make sure to firmly close the clamp and park it across travel  

  direction when at rest.

• Make sure that the grapple is hanging free so that swinging   

  to both sides is possible during travel on uneven 

  ground/terrain.

3.  SAFETY RULES

Содержание HRZ Kombi Anbau

























Отзывы: