BFT GIOTTO BT A ULTRA 36, Инструкция по установке и эксплуатации

Страница: 28 / 64

ENGLISH
1) TECHNICAL SPECIFICATIONS
BARRIER
Power supply
110-120V~ 50/60Hz
220-230V~ 50/60 Hz(*)
Motor voltage 24V
Power absorbed
300W
Internal lubrication permanent grease
Max torque 280-290 Nm
Impact reaction Electronic torque limiter
Minimum opening time 2,2s
Boom length
from 2 to 6 metres
Manual mechanical release
customised key
Type of boom
BOOM ES, BOOM PS
Limit devices
electromechanical
Maximum usage cycle
3-metre bar 5000 operations / 24h
6-metre bar 2000 operations / 24h
Buffer batteries (optional extras) Two 12V 1.2Ah batteries
Environmental conditions from -20°C to +55°C
Degree of protection IP 54
Noise level <70dBA
Weight (without boom)
41 Kg
Dimensions see fig. B
CONTROL UNIT
Mains/low voltage insulation > 2MOhm 500V
Dielectric strength mains/low voltage 3750V~ for 1 minute
Thermal overload protection Software
Supply to accessories
24V ~ (demand max. 0,5A)
24V ~ safe
AUX 0
NO 24V ~ powered contact
(max.1A)
AUX 3 N.O. Contact (24V~ /1A max)
Barrie-open warning light
24V~3W max
Blinker
24V~25W max
Fuses see Fig. I
N° of combinations 4 billion
Built-in Rolling-Code radio-receiver frequency 433.92MHz
Max. n° of remotes that can be memorized 63
Setting of parameters and options Universal handheld programmer/
LCD display
(*)= special power supply voltages on request.
2) ELECTRICAL INSTALLATION SET-UP
WARNING: before opening the door, the spring must be unloaded
(vertical boom). Set up the electrical installation (fig. A) with reference to
the current regulations for electrical installations. Keep the mains power
supply con-nections definitely separate from the service connections
(photocells, electric edges, control devices etc.).
Fig. A shows the number of connections and section for a 100m length
of power supply cables; for greater lengths, calculate the section for the
true automation load. When the auxiliary connections exceed 50 metre
lengths or go through critical disturbance areas, it is recommended to
decouple the control and safety devices by means of suitable relays.
WARNINGS -
When performing wiring and installation, refer to the stan-
dards in force and, whatever the case, apply good practice principles.
Wires carrying different voltages must be kept physically separate from
each other, or they must be suitably insulated with at least 1mm of ad-
ditional insulation.
Wires must be secured with additional fastening near the terminals,
using devices such as cable clamps. All connecting cables must be kept
far enough away from dissipaters.
3) CONNECTION (Fig. I)
Once suitable electric cables have been run through the raceways and
the automated device’s various components have been fastened at the
predetermined points, the next step is to connect them as directed and
illustrated in the diagrams contained in the relevant instruction manuals.
Connect the live, neutral and earth wire (compulsory). The mains cable
must be clamped in the relevant cable gland, and the accessories’ wires
in the cable gland, while the earth wire with the yellow/green-coloured
sheath must be connected in the relevant terminal.
WARNING:
The electrical connections must be carried out workmanlike
by qualified experienced personnel, in conformity with all the current
standards and with the use of appropriate materials.
Lay out the electrical installation with reference to the current electrical
standards.
Keep the mains supply connections clearly separated from the service
connections.
In the initial section of the electrical installation, fit a circuit breaker with
a contact opening distance equal to or greater than 3,5 mm, provided
with magnetothermal protection and a differential switch having ad-
equate capacity for the appliance consumption. For the wiring, only
use cables conforming to the harmonised or national standards, having
a cross section corresponding to the initial protection, the appliance
consumption and the installation conditions, for example a 3x1.5 sq
mm (H 05 VV-F) cable.
Terminal Definition Description
Po
w
er supply
L LINE
Single-phase power supply
220-230V ~50/60 Hz*
N NEUTRAL
JP31
TRANSF PRIM Transformer primary winding connection, 220-230V
~
.
JP32
JP13 TRANSF SEC
Board power supply:
24V~ Transformer secondary winding
M
ot
or
10 MOT +
Connection motor
11 MOT -
Au
x
20
AUX 0 - 24V POWERED CONTACT
(N.O.) (MAX. 1A)
AUX 0 configurable output - Default setting FLASHING LIGHT.
2ND RADIO CHANNEL/ SCA GATE OPEN LIGHT/ COURTESY LIGHT command/ ZONE LIGHT command/ STAIR LIGHT/
GATE OPEN ALARM/ FLASHING LIGHT/ SOLENOID LATCH/ MAGNETIC LOCK/ MAINTENANCE/ FLASHING LIGHT AND
MAINTENANCE / BARRIER STATUS OUTPUT/LIGHTS ON BAR. Refer to “AUX output configuration” table.
21
26
AUX 3 - FREE CONTACT (N.O.)
(Max. 24V 1A)
AUX 3 configurable output - Default setting 2ND RADIO CHANNEL Output.
2ND RADIO CHANNEL/ SCA GATE OPEN LIGHT/ COURTESY LIGHT command/ ZONE LIGHT command/ STAIR LIGHT/
GATE OPEN ALARM/ FLASHING LIGHT/ SOLENOID LATCH/ MAGNETIC LOCK/ MAINTENANCE/ FLASHING LIGHT AND
MAINTENANCE/ BARRIER STATUS OUTPUT/LIGHTS ON BAR. Refer to “AUX output configuration” table.
27
Limit
swit
ches
41 + REF RIF Common references
42 RIFC Reference closing RIFC (N.C.)
43 RIFO Reference opening RIFO (N.C.)
A
cc
essories po
w
er
supply
50 24V-1~/-24V
Accessory power supply output. The accessory power supply is in A.C. (~) when the board is powered via the mains voltage,
and D.C. (
) during battery operation.
51 24V-2~/+24V
52 VSAFE 24V-2~/+24V
Power supply output for checked safety devices (photocell transmitter and safety edge transmitter).
Output only active during the operation cycle. The supply to the checked device is via terminals 50-52.
Commands
60 Common IC 1 and IC 2 inputs common
61 IC 1
Configurable command input 1 (N.O.) - Default OPEN.
START E / START I / OPEN / CLOSE / TIMER / OPEN
Refer to the “Command input configuration” table.
62 IC 2
Configurable command input 2 (N.O.) - Default CLOSE.
START E / START I / OPEN / CLOSE / TIMER / OPEN
Refer to the “Command input configuration” table.
28
GIOTTO BT A ULTRA 36
D814017 2F
A00_02