357
7) RADIO TECHNICAL SPECIFICATIONS
Frequency .............................................................................. : 433.92MHz
Coded by means of ............................................. : Rolling-code algorithm
No. combinations ....................................................................... : 4 milliard
Antenna impedance ........................................................ : 50Ohm (RG58)
Max no. radio transmitters to be memorised: ........................................ 63
Receiver output channels:
-
output channel 1, if activated, controls a START command.
-
output channel 2, if activated, controls the excitation of the 2nd radio
channel relay for 1s, or activates the pedestrian function, depending on
the setting.
Transmitter versions which can be used:
- MITTO Transmitter
MITTO2
–
double-channel, MITTO4
–
four-channel.
Keys ............................................................................................... : Yellow
Power supply ............................... : 2 3V Lithium batteries (CR2016 type)
Range ............................................................................. : 50 / 100 metres
- TRC Transmitter
TRC1-single-channel, TRC2- double-channel, TRC4- four-channel.
Keys: .................................................................................................. : Red
Power supply: .......................................................... : 12V Alkaline battery
Range: ............................................................................ : 50 / 100 metres
ANTENNA INSTALLATION
Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG8 coaxial cable.
The presence of metallic masses next to the antenna can interfere with
radio reception. In case of insufficient transmitter range, move the antenna
to a more suitable position.
8) RECEIVER CONFIGURATION
The
Clonix64
receiver combines the characteristics of utmost safety in
copying variable code (rolling code) coding with the convenience of
carrying out transmitter
“
cloning
”
operations thanks to an exclusive system.
Cloning a transmitter means creating a transmitter which can be included
automatically within the list of the transmitters memorised in the receiver,
either as an addition or as a replacement of a particular transmitter.
Cloning by replacement is used to create a new transmitter which takes the
place of the one previously memorised in the receiver; in this way the lost
transmitter is removed from the memory and will no longer be usable.
Therefore it will be possible to remotely program a large number of
additional transmitters, or for example, replacement transmitters for those
which have been lost, without making changes directly to the receiver.
When coding safety is not a decisive factor, the Clonix receiver allows you
to carry out fixed code additional cloning, which although abandoning the
variable code, provides a high number of coding combinations.
PROGRAMMING
Transmitter storage can be carried out in manual mode, or by means of the
UNIRADIO
programmer which allows you to create installations in the
“
collective receivers
”
mode, as well as manage the complete installation
database using the
EEdbase
software.
The
Clonix 64
receiver is programmed by connecting
UNIRADIO
to the
ALTAIR
control panel, using the
UNIFLAT
and
UNIDA
accessories, as
shown in fig. 4.
9) MANUAL PROGRAMMING
In the case of standard installations where advanced functions are not
required, you can proceed to manual storage of the transmitters, making
reference to fig. B for basic programming.
-
If you wish the transmitter to activate output 1 (START) by means of
key1 and output 2 (2nd ch. relay) by means of key2, enter the transmitter
in menu
“
key1=Start key2=2nd ch.
”
, as in fig. B.
-
If you wish the transmitter to activate output 1 (START) by means of
key1, key2, key3 or key4, enter the transmitter in menu
“
Start key
”
, as
in fig. B.
-
If you wish the transmitter to activate output 2 (2nd radio channel relay)
by means of key1, key2, key3 or key4, enter the transmitter in menu
“
2nd
ch. key
”
, as in fig. B.
Note:
Hidden key P1 appears differently depending on the transmitter
model.
For
TRC 1-2 / MITTO 2-4
, press hidden key P1 (fig. 4). For
TRC 4
, the
key P1 function corresponds to simultaneously pressing the 4 transmitter
keys or, after opening the battery compartment, bridging the two P1
points by means of a screwdriver (fig. 4).
IMPORTANT NOTE: ATTACH THE ADHESIVE KEY LABEL TO THE
FIRST MEMORISED TRANSMITTER (MASTER).
In the case of manual programming, the first transmitter assigns the key
code to the receiver; this code is necessary in order to carry out subsequent
cloning of the radio transmitters.
10) RADIO TRANSMITTER CLONING
Clones can be added by means of UNIRADIO, and the only limitation to this
is the maximum number of transmitters the receiver can memorise.
Note: in rolling-code cloning, the level of safety of the code anti-copying
system is very high, and is the same as that of the transmitters memorised
manually in the receivers.
Knowledge of the cloning
key code
or the reading from the key transmitter
allow the operator to create additional clones by remote control, without
needing further information.
To create replacement clones, you need to have the complete receiver
memory data; therefore, if you plan to carry out replacement cloning
operations by remote control, you need to memorise the contents of the
receiver memory by reading it using
UNIRADIO
and entering it in the
EEdbase
database.
When assigning a specific key on an additional clone transmitter to a
specific output channel on a receiver, a predefined procedure is followed.
This procedure can be modified as required if radio transmitter storage is
carried out by means of
UNIRADIO
, or otherwise it is identical to the
procedure for the first transmitter, the one with the KEY TRANSMITTER
LABEL.
The keys on the replacement clone transmitter maintain the same association
with the output channels of the receiver as the replaced transmitter.
Code reading:
In the case where a receiver code in not known, reading can be obtained
by proceeding in the following way.
1) Switch
UNIRADIO
on and wait for the welcome message.
2) Use the
<arrow up>
and
<arrow down>
keys to select item
<go the
menu number>.
3) Press
<enter>.
4) When in the subsequent menu, type number
225
and press
<enter>
.
5) Follow the instructions appearing on the
UNIRADIO
display.
Having carried out key code reading, you are advised to write it down on the
appropriate card supplied and given to the user (Fig.6).
10.1) Cloning with rolling-code
a) Cloning by addition with code
For practical clone creation, refer to instructions on the UNIRADIO device
or, for clone addition, observe the following simplified procedure:
1) Switch
UNIRADIO
on and wait for the welcome message.
2) Use the
<arrow up>
and
<arrow down>
keys to select item
<go the
menu number>
.
3) Press
<enter>
.
5) When in the subsequent menu, type number
2121
and press
<enter>
.
6) Follow the instructions appearing on the
UNIRADIO
display.
b) Cloning by addition with master
For practical clone creation by means of the master transmitter (marked
with the key label) refer to the instructions on the UNIRADIO device, or
observe the following simplified procedure:
1) Switch
UNIRADIO
on and wait for the welcome message.
2) Use the
<arrow up>
and
<arrow down>
keys to select item
<go the
menu number>
.
3) Press
<enter>
.
5) When in the subsequent menu, type number
2122
and press
<enter>
.
6) Follow the instructions appearing on the
UNIRADIO
display.
10.2) Cloning with fixed code
NOTE: ALTHOUGH A HIGH NUMBER OF COMBINATIONS FOR
TRANSMITTER CODING IS INCLUDED IN THE FIXED CODE
CONFIGURATION, THE SAFETY LEVEL OF THE CODE ANTI-COPYING
SYSTEM IS INFERIOR.
In the cases where you do not wish to manage the list or the cloning key or
the key transmitter, additional clones can be generated by means of
UNIRADIO, starting from any transmitter which is already memorised
within the system.
This operation can only be carried out if the receiver is configured to operate
with a fixed code (no longer a rolling code).
To do this, you must activate the FIXED CODE option in the logic menu, see
fig. A.
To activate it through UNIPRO:
Enter the
“
CONTROL UNITS
”
menu, the
“
LOGICS
”
submenu and the
“
SPECIAL LOGICS
”
submenu; then scroll the display screenfuls using the
up/down arrows to set the numerical values of:
D811321_04
ALTAIR
ALTAIR
CONTROL UNITS
CONTROL UNITS
