355
ALTAIR
ALTAIR
Thank you for buying this product, our company is sure that you will be more
than satisfied with its performance.
This product is supplied with an
“
Instruction Manual
”
which should be read
carefully as it provides important information about safety, installation,
operation and maintenance.
This product complies with recognised technical standards and safety
regulations. We declare that it is in conformity with the following European
Directives: 89/336/EEC, 73/23/EEC and subsequent amendments.
1) GENERAL SAFETY
WARNING! An incorrect installation or improper use of the product
can cause damage to persons, animals or things.
•
The
“
Warnings
”
leaflet and
“
Instruction booklet
”
supplied with this
product should be read carefully as they provide important information
about safety, installation, use and maintenance.
•
Scrap packing materials (plastic, cardboard, polystyrene etc) according
to the provisions set out by current standards. Keep nylon or polystyrene
bags out of children
’
s reach.
•
Keep the instructions together with the technical brochure for future
reference.
•
This product was exclusively designed and manufactured for the use
specified in the present documentation. Any other use not specified in
this documentation could damage the product and be dangerous.
•
The Company declines all responsibility for any consequences resulting
from improper use of the product, or use which is different from that
expected and specified in the present documentation.
•
Do not install the product in explosive atmosphere.
•
The construction components of this product must comply with the
following European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC
and subsequent amendments. As for all non-EEC countries, the above-
mentioned standards as well as the current national standards should
be respected in order to achieve a good safety level.
•
The Company declines all responsibility for any consequences resulting
from failure to observe Good Technical Practice when constructing
closing structures (door, gates etc.), as well as from any deformation
which might occur during use.
•
The installation must comply with the provisions set out by the following
European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC and
subsequent amendments.
•
Disconnect the electrical power supply before carrying out any work on
the installation. Also disconnect any buffer batteries, if fitted.
•
Fit an omnipolar or magnetothermal switch on the mains power supply,
having a contact opening distance equal to or greater than 3mm.
•
Check that a differential switch with a 0.03A threshold is fitted just before
the power supply mains.
•
Check that earthing is carried out correctly: connect all metal parts for
closure (doors, gates etc.) and all system components provided with an
earth terminal.
•
Fit all the safety devices (photocells, electric edges etc.) which are
needed to protect the area from any danger caused by squashing,
conveying and shearing.
•
Position at least one luminous signal indication device (blinker) where
it can be easily seen, and fix a Warning sign to the structure.
•
The Company declines all responsibility with respect to the automation
safety and correct operation when other manufacturers
’
components
are used.
•
Only use original parts for any maintenance or repair operation.
•
Do not modify the automation components, unless explicitly authorised
by the company.
•
Instruct the product user about the control systems provided and the
manual opening operation in case of emergency.
•
Do not allow persons or children to remain in the automation
operation area.
•
Keep radio control or other control devices out of children
’
s reach, in
order to avoid unintentional automation activation.
•
The user must avoid any attempt to carry out work or repair on the
automation system, and always request the assistance of qualified
personnel.
•
Anything which is not expressly provided for in the present instructions,
is not allowed.
1) GENERAL OUTLINE
The
ALTAIR
control panel is suitable for swing gates. It is supplied by the
manufacturer with standard functional settings. Any alteration must be set
by means of the incorporated display programmer or by means of
UNIPRO
and
UNIRADIO
. The Control unit completely supports the
EELINK
protocol.
The most significant innovative characteristics of the Altair control panel are:
-
management of two motors with electronic torque setting, see paragraph3
-
management of on-board receiver, according to the new type of radio-
control cloning, see paragraph 8
-
presetting for operation with local or centralised controls via wire, see
paragraph 11.
Its main characteristics are:
-
Power supply: 230V
±
10% 50Hz (other voltages on request)
-
No-load absorption from the mains: 0.2A max
-
Maximum power with 2 motors: 300W each
-
Maximum power with 1 motor: 300W
-
Motor force limitation: to be set electronically
-
Blinker output: 40W max
-
Gate-open warning light output: 24V
3W max
-
Supply output for accessories: 24V
5VA max
-
Manoeuvre limit switch: with operation time limitation, operation time to
be set
-
Safety inputs: Stop, photocells
-
Control inputs: Start, pedestrian
-
Operational options: various, depending on the settings and controls
applied
-
Radio receiver: 433.92 MHz rolling-code or fixed code
-
Maximum numbers of radio control devices to be managed: 63
-
Centralised controls with other controllers: presetting for serial protocol
with an external accessory.
3) CONTROL UNIT TECHNICAL SPECIFICATIONS
Power supply: ........................................................... 230V
±
10% 50Hz*
No-load absorption from the mains: ............................................ 0.2A max
Mains/low voltage insulation: ....................................... > 2MOhm 500Vdc
Dielectric strength: ..................... mains/low voltage 3750Vac for 1 minute
Motor output current: ...................................................... 1.25A+1.25Amax
Motor relay commutation current: ........................................................ 10A
Maximum power with 2 motors: ............................................ 300W+300W
Maximum power with 1 motor: ....................................................... 300W
Blinker: ........................................................................................ 40W max
Gate-open warning light: ................................................... 24V
3W max
Supply to accessories: ................................ 24V
(0.2A max absorption)
Degree of protection for box: ............................................................ IP 55
Dimensions: ............................................................................. see figure 1
Fuses: ...................................................................................... see figure 2
(*other voltages available on request)
4) TERMINAL BOARD CONNECTIONS (Fig.3)
WARNING -
During wiring and installation operations, refer to the current
standards and to principles of good technical practice.
Wires powered at different voltages must be physically separated, or
suitably insulated with at least 1 mm extra insulation. The wires must be
clamped by an extra fastener near the terminals, for example by bands.
WARNING! For connection to the mains, use a multipolar cable with
a minimum of 3x1.5mm
2
cross section and complying with the
previously mentioned regulations. For example, if the cable is out side
(in the open), it has to be at least equal to H07RN-F, but if it is on the
inside (or outside but placed in a plastic cable cannel) it has to be or
at least egual to H05VV-F with section 3x1.5mm
2
.
JP7
1
GND terminal
2-3
Single-phase mains supply (2=L) (3=N)
JP8
4-5-6
Connection to motor 1:
4 on 1
5 common (blue)
6 on 2
7-8-9
Connection to motor 2:
7 on 1
8 common (blue)
9 on 2
10-11
230Vac output for blinker light (40W max)
JP9
13-14
24V
200mA max output
–
supply to photocells or other devices
15-16
Output (N.O. contact (24V
/0.5A max)) for gate-open warning
light or, alternatively, 2nd radio channel (see paragraph 6
“
configuration
”
)
17-18
STOP pushbutton (N.C.) input. If not used, leave the bridge
connected.
D811321_04
CONTROL UNITS
CONTROL UNITS
