manualshive.com logo in svg

Bevent Rasch RCKD, Быстрый старт, Страница: 7 / 7

Поделиться
Скачать
Bevent Rasch RCKD Скачать руководство пользователя страница 7

7

BORÅS

 

Tel +46 (0)33 - 23 67 80      

STOCKHOLM

 

Tel +46 (0)8 - 54 55 12 70

1.  Install the damper in the duct.

2.  Duct going through supporting construction, is fastened 

using brackets. Seal according to applicable require-
ments, such as caulking with mineral wool, min 40 kg/
m

3

 and fire stopping sealant.

3.  If fire damper is not connected to the duct system, fit 

non-combustible grilles designed for the damper on the 
unconnected sides. The minimum distance between 
the damper blade in the open position and the grille is 
50 mm.

4.  Install the thermal sensor with the sensor body in the air 

flow without obstructing the movement of the damper 
blade. 

Installation in horizontal duct.

Damper’s fire resistance class: EI60 (ve i <–> o) S.

EC certificate 0402-CPD-SC0900-13

5.  Duct is fastened/supported according to applicable 

 requirements. 

6.  Insulate the duct according to applicable requirements 

using instructions from the insulation supplier, min.  
80 mm and 55 kg/m

3

. Note that insulation must cover 

the damper.

• 

Minimum distance between dampers must be

 200 mm.

• 

Minimum distance to joist structure/wall must be

 75 mm.

•  The damper spindle may be installed in any position.

d+40

Duct

Duct

Seal acc. to

section 2

Support of duct,

see section 5

Seal with fire

stopping sealant, 

e.g. Intumex AN

(Possible protective grille,

see section 3)

Insulation equivalent to 

fire resistance class of the

supporting construction

Brackets

Max. 1000 mm

Installation instruction

EI60

Fire damper BSKC6

13-0184_ENG / Sept. 2017   teamfr

ont.se

Содержание RCKD








Отзывы:

Нет отзывов