Better Water EQROPB01600 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 84

background image

Better Water LLC; rev. Jul 2019

Page 54 of 80

PB2

– Mediport Portable RO Operator Manual

CONSEQUENTIAL, INCIDENTAL, ECONOMIC, DIRECT, INDIRECT, GENERAL OR SPECIAL
DAMAGES, WHICH ARE HEREBY EXPRESSLY DISCLAIMED.

HOW TO OBTAIN A REPLACEMENT PART UNDER LIMITED WARRANTY

a. Buyer should contact the Customer Service or Technical Support Departments and request a
Return Goods Authorization.
b. Described part(s) will be sent with a purchase order.
c. The returned part(s) will be returned to the factory for limited warranty consideration. If part(s)
are not covered under the limited warranty, part(s) will be considered billable against the
purchase order supplied.

WHAT IS NOT COVERED BY THIS LIMITED WARRANTY:

By way of example and not limitation, this limited warranty does not cover:



Damage to or replacement of any ion exchange resin of filter media



Labor or service charges for the removal and/or replacement of any defective parts after
the ninety (90) day period from the date of installation or sale by Better Water LLC



Freight charges and travel expenses



Damage from inadequate or defective wiring, improper voltage, improper connections or
electrical service, inadequate or defective plumbing, water supply, or water pressure, or
in violation of applicable building, plumbing or electrical codes, laws, ordinances or
regulations.



Damage from improper installation or operation, including but not limited to, abuse,
accident, neglect, improper maintenance, freezing and fires, or abnormal use.



Damage caused by contaminants in Buy

er’s water supply, including hardness, chlorine,

chloramines, sulfur, bacterial iron, tannin, algae, oil, organic matter or other unusual
substances, if special equipment has not been installed by Better Water LLC to remove
such contaminants



Damage to or caused by filters/membranes or other replacement parts not purchased
from Better Water LLC or damage caused by modification, alteration, repair or service of
the equipment or any of its parts by anyone other than Better Water LLC or its expressly
authorized representatives.

«
...
56
57
58
59
60
...
»

Содержание EQROPB01600





















































































Отзывы:

Нет отзывов

Похожие инструкции для EQROPB01600

Бренд: Daewoo Страницы: 9

Бренд: dafi Страницы: 12

Бренд: A-Star Страницы: 29

Бренд: A.O. Smith Страницы: 6

Бренд: AMICUS Страницы: 12

Бренд: FCI Страницы: 20

DSE-5 THRU DSE-120

Бренд: A.O. Smith Страницы: 24

Бренд: clage Страницы: 148

Бренд: DOCRILUC Страницы: 31

Бренд: Franke Страницы: 3

HAC8EECQ 1E Series

Бренд: Halsey Taylor Страницы: 6

Commercial COOL CCBL01

Бренд: W APPLIANCE Страницы: 16

Бренд: Halsey Taylor Страницы: 7

DAIRY WATER HEATER

Бренд: COTSWOLD Страницы: 2

FUTERA II Series

Бренд: RBI Страницы: 48

STEAMIN' HOT H-SH10-SS

Бренд: Emerson Страницы: 6

InSinkErator DS200

Бренд: Emerson Страницы: 2

Бренд: Emerson Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды