background image

5

5. 1 Bulit-in Bayang Receiver

Lite 1S brushed FC is with build-in Bayang protocol receiver. The communication
protocol should be set as Bayang protocol when using built-in Bayang receiver, as
follows:

Press the FC key on the bottom of the FC and plug the battery at the same time

Release the FC key after 4 seconds

Once “Bayang” shown on OSD information interface, FC will receive the

built-in Bayang receiver data

How to bind:

Please ensure that the the receiver communication protocol is in Bayang

protocol

Power on the FC board and the Built-in Bayang receiver will enter binding

status auto

Make your radio transmitter enter bind status

Once binding successfully, receiver LED will off

5. 2 SBUS Protocol

Supports SBUS protocol, including Frsky XM/ XM+ receiver, Futaba receiver. Here
is the diagram with SBUS protocol receiver:

The communication protocol should be set as SBUS protocol when using the external
SBUS protocol receiver, as follows:

Press the FC button on the bottom of the FC and plug the battery at the same

time

Release the button and press the FC button again within 4 seconds

Once “SBUS” shown on OSD information interface, FC will receive the

external receiver data via SBUS protocol

Содержание Lite brushed V2 FC

















Отзывы: