S-S-003587
S-S-003587/21x28.5cm/
54138NN 54144NN 欧规SPA说明书
/JS-YF-2015-B-04514
/英
13
I
Pressing the Temperature Increase or Decrease buttons will
cause the LED to flash. When it is flashing you can adjust to
the desired temperature setting. If you hold these buttons
down, the values will rapidly increase or decrease. The new
and desired temperature setting will remain on the LED
display for 3 seconds to confirm the new value.
NOTE:
The default temperature is 35°C (95°F).
NOTE:
Temperature adjustment ranges from 20°C (68°F) to
40°C (104°F).
Temperature Adjustment Buttons
The pump has a 5-minute auto-lock. To lock or
unlock the pump, place a finger over the
lock/unlock button for 3 seconds.
Lock/Unlock Button
A
E
Water Filter Button
C
HydroJet System Button
This button turns the filter pump on and off.
The light above the Water Filter Button
displays red when activated.
This button turns the water pump on and off.
The light above the HydroJet system button
displays red when activated.
Celsius/Fahrenheit Toggle
The temperature can be displayed in either Celsius or Fahrenheit.
H
Use this button to activate the heating system.
When the light above the heat button is red, the
heating system is activated. When the light is
green, the water is at the set temperature and the heating
system is at rest.
NOTE:
If the heating system is activated, the filtration system
will automatically start.
NOTE:
After turning off the heating system, the filtration
system will continue to operate.
NOTE:
The Lay-Z-Massage System will automatically shut off
when the heater is activated.
Heat Button
D
Use this button to activate the massage system,
which has a 30-minute auto-shutoff feature.
The light above the Lay-Z-Massage System
Button displays red when activated.
Lay-Z-Massage System Button
(
For Hydro-Jet Pro
)
IMPORTANT:
Do not run the
Lay-Z-Massage system when the cover is
attached. Air can accumulate inside the
spa and cause irreparable damage to the
cover and bodily harm.
B
INSTRUCTIONS FOR Power-Saving
Timer Button
G
After 72 hours of operation, the pump will
hibernate and flash “End” with the current water
temperature. When the pump is hibernating both
the heating and water filter functions are disabled. To re-active
the pump press lock/unlock button for 3 seconds.
Press this button for 2 seconds to active the control panel
bottons and the light turns to green. Press this button for 2
seconds to turn off all currently activated functions.
On/Off Button
K
J
Power-Saving Timer LED
When the light flickers, the Power-Saving Timer function is being set.
When the light is on, the Power-Saving Timer function is set.
Once powered up, the LED displays the current
water temperature automatically.
NOTE:
Test the water regularly and make sure the free
chlorine level is between 2-4 ppm.
NOTE:
Do not press any buttons on the panel and attach the SPA
cover during the chlorinating progress. You can re-adjust the
working duration by pushing the Salt Chlorinator System Button.
LED Display
L
K
A
L
C
J
D
I
E
H
F G
F
Salt Chlorinator System Button
Use this button to turn on the Salt Chlorinator
System and set the working duration. You can set
the working duration from 3 hours to 5 hours to 8
hours by pushing the Salt Chlorinator System
Button. After setting the working duration, the Salt
Chlorinator System will start to work automatically.
B
K
A
L
C
J
D
I
E
H
F G
HYDROJET PRO
HYDROJET
Note:
The system will shut off automatically after 1 hour.
Note:
Do not dry run the HydroJet System.
NOTE:
The built-in hard water treatment function
works automatically.
This is a newly added function, designed to help avoid
wasting power by setting the time and duration of the
heating cycle for the spa.
This way, you can enjoy your spa at the time you desire,
without needing to leave the heater on at all times.
STEP 1:
Set the heating duration
1. Press the button unit the LED starts to flash.
2. Press the or button to adjust the heating duration
(From 1-48 hours).
3. Press the button again to confirm the heating duration.
STEP 2:
Set the number of hours FROM NOW when the heater will activate
1. After setting the heating duration, the LED starts to flash.
2. Press the or button to adjust the hours until time of activation
(From1-24 hours).
3. Press button again or simply touch nothing for 10 seconds to confirm
the setting.The LED will light steadily, and the countdown to heater
activation will begin.
To modify the timer settings:
Press the button and use the or
button to adjust.
Cancel the setting:
Press the button for 2 seconds.
NOTE:
After setting, the screen flashes the current temperature and time alternately.
NOTE:
Timer adjustment (amount of time with the heater ON) may be set from 0 to
48 hours; Reservation time adjustment (the number of hours FROM NOW when the
heater will begin to function) may be set from 0 to 24 hours. If the timer is
set at 0 hour, it means the Timer function is not set.
Note that the timer is one time per use - the user sets the duration of the
heating cycle, and how many hours from now the heating cycle begins. The
timer does NOT repeat until reset.
