BeSense X32_ZWAVE Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 12

background image

ix32

Zwave PLUS Ceiling PIR Sensor

I. Introduction

X32_ZWAVE wireless PIR sensor adopts latest detection & induction technologies
including Energy Accumulation Management, Dynamic Random Time Division
Technology etc. And it combines multi-zones comprehensive induction calculation and
uses advanced MCU digital processing technology. Besides, it has the advantages of
stable & reliable detection, low false alarm and pet immune.

• Special Fresnel lens with patented technology, built-in far infrared wave with above

95% transmittance rate

• Adopt original imported Heimann sensor from Germany, with high sensitivity & low

false alarm

• Real anti-visible light technology, no false alarm under 6500LUX strong light

interference With sealed induction cavity design, prevent false alarm caused by
thermal current interference

• Configurable detection sensitivity, suitable for variety of detection environments With

fuzzy logic algorithm & fuzzy recognition technology, pet-immune Ultra-low power
consumption, 2 years of battery working life

[email protected]

1
2
3
...
»

Содержание X32_ZWAVE













Отзывы:

Нет отзывов

Похожие инструкции для X32_ZWAVE

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 3

ECONAVI CZ-CENSC1

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 9

AR42P9W - Plasma Panel anti-glare Filter

Бренд: Panasonic Страницы: 5

Бренд: Tamron Страницы: 3

Бренд: Panasonic Страницы: 2

Бренд: Hama Страницы: 2

Wireless Temperature/Humidity Station

Бренд: DAVIS Страницы: 8

Бренд: Echo Страницы: 4

smartsensor advance

Бренд: Wavetronix Страницы: 2

Бренд: X-lite Страницы: 5

Бренд: Eaton Страницы: 11

Multi Function Professional Puncher-A1

Бренд: Canon Страницы: 44

NNC994S - Genius Prestige - Convection Microwave...

Бренд: Panasonic Страницы: 1

Бренд: Gared Страницы: 10

Бренд: Vortice Страницы: 132

LCD Touch BacPac

Бренд: GoPro Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды