Bernard Burton Spirit of Pitts Скачать руководство пользователя | Manualshive

Страница: 2 / 11

background image

© 2005 - Bernard Burton DRAFT

2

The plans

can be requested via this link

http://www.gundersonaerodesign.com/m12plansreq.htm

The laser kit

is available here

http://www.gundersonaerodesign.com/

. Gunderson AeroDesign is a

company located in Vista, CA dedicated to the radio controlled aircraft hobby.

Note

This assembly manual is not intended to tell you how to build this aircraft, each builder has their own approach to building. This is only a guide

which will show you how we built our Spirit of Pitts. Use it if you feel that it may help.

NOT ALL STEPS ARE SHOWN IN THIS MANUAL.

Disclaimer

This plane and plans are intended for ADVANCED BUILDERS and PILOTS ONLY !

The user shall determine the suitability of the product for their intended use, and shall assume all risk and liability in connection therewith. The

builder assumes all risk of injury when building this plane.

«
1
2
3
4
...
»

Содержание Spirit of Pitts












Отзывы:

Нет отзывов

Похожие инструкции для Spirit of Pitts

Бренд: Jamara Страницы: 12

Бренд: Xray Страницы: 48

Jim-Loader+Trailer 800056516

Бренд: BIG Страницы: 12

Бренд: Madcow Rocketry Страницы: 4

Grange Farm Tipper Wagon

Бренд: Bole Laser Craft Страницы: 6

Бренд: Raptor Страницы: 41

mini Black Brant II

Бренд: Madcow Rocketry Страницы: 3

Бренд: Angling Technics Страницы: 3

Бренд: Eduard Страницы: 4

Gloster Meteor F.4 interior S.A.

Бренд: Eduard Страницы: 2

Бренд: TWM Страницы: 15

F4U-1D interior 1/32

Бренд: Eduard Страницы: 4

Play & Go Puppy Salon

Бренд: VTech Страницы: 14

North German Holiday Home

Бренд: Faller Страницы: 8

SpinX Stuntcar 2,4GHz

Бренд: Jamara Страницы: 8

National Geografic NG300 OURANOSAUR

Бренд: Laser Pegs Страницы: 29

Бренд: Spin Master Страницы: 4

Magic Wand Laptop

Бренд: VTech Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды