background image

14

2. Operation Interval:

On the days of the week screen press the 

 button to 7 times 

for skipping the operation by days of the week and advancing  
the cursor to the Days Cycle line. Two numbers appear on this 
line: the right number presents the program’s Days Interval 
and the left number display the number of days left till the next 
operation day. Note that during the first setup of this program  
the number of day till next operation number is zero.

Use the 

 and the 

 buttons to set the required Days Interval  

(10 days in our example). Note that the maximal interval is  
30 days.

Press the 

 button to move to the next programming screen 

which is the Start Times screen.

3. Start Time:

Use the 

 and the 

 buttons to set the required Start Time  

(08:00 in our example).

The controller is now set for automatically operating this  
Dead-end Pipes Purging Application. 

C. Purging interval by days of the week and purging 
amount by Water Volume:

In this example the pipe needs to be purged for 50 water 
meter pulses every Monday and Friday at 08:00 AM. Therefore, 
the three required program parameters of the controller are: 
Operation Volume - 50 pulses, Operation Days - Monday and 
Friday, and Start Time at 08:00 AM.  

In order to operate the above program the system should be 
based on BERMAD’s series Hydrometer, or on other BERMAD’s 
control valve and a water meter. The Subtv controller should be 
also set to volumetric operation, which can be done only at the 

Содержание Subtv

























Отзывы: