background image

12

Dead-end Pipes Purging Application Settings 

Due to operational conditions, in some municipal and industrial 
water systems, there is a need for periodic purging of the 
systems dead-ends of pipes for refreshing the water supply. 
BERMAD’s control valves equipped with Subtv controllers can be 
installed in these systems. BERMAD’s Dead-end Pipes Purging 
Application accounts for the purging out of the system. This task 
is automatically performed based on three major parameters:

1. Purging interval - set at specific days of the week or as  

day’s interval

2. Amount of purged water - set by operation time or by volume

3. Start time - set for the operation day (with up to three start 

times per such day)

The following examples depict three typical scenarios:

A. Purging interval by Days of the Week and purging 
amount by operation time:

In this example the pipe needs to be purged for 5 minutes every 
Monday and Friday at 08:00 AM. Therefore, the three required 
program parameters of the controller are: Operation Time - 5 
Minutes, Operation Days - Monday and Friday, and Start Time  
at 08:00 AM.  

1. Operation Time:

Use the 

 button to move to the Operation Time programming 

screen - this is the screen with blinking 

 icon, blinking triangle 

with the digit 1 in it and the 

 icon. Use the 

 

and the 

 

buttons to set the required operation time (00:05 minutes in  
our example).

Press the 

 button to move to the next programming screen 

which is the Operation Days screen.

Содержание Subtv

























Отзывы: