manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, Руководство пользователя

Поделиться
Скачать
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM Скачать руководство пользователя страница 26

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

26

 

5. 

Connection 

  WARNING 

Uncontrolled and unpredictable operational behaviour! 

Failure of certain components in electronic control systems may result in uncontrolled and unpredictable 
operational behaviour. 

 

All types of failure and the associated protection systems must be taken into account at system level. 

 

Comply with all automation system manufacturer instructions. 

5.1.  Power supply 

The device is powered by an external 24 V DC power supply. It is not designed to be connected to a 
DC mains supply. 
 

 

Before plugging in the device, ensure that the external power supply meets the required specifi-
cations (type K to 61131-2). 

 
 

External power supply (24 V DC) 

Supply voltage 

+24 V DC SELV (

–15% / +20%) 

Ripple current propor-

tion 

Max. 5 % 

The direct voltage level must not fall below 20.4 V. 

Power consumption

 

ET2110W X CS: Total max. 0.6 A at +24 V DC (peak current 1.2 A) 

ET2115WUX CS: Total max. 0.7 A at +24 V DC (peak current 1.2 A) 

DC2110W X CM: Total max. 0.8 A at +24 V DC (peak current 1.2 A) 

DC2115WUX CM: Total max. 0.9 A at +24 V DC (peak current 1.2 A)

 

 
 

Internal power supply 

A power supply for the system electronics for an input voltage of 24 V DC (–15% / +20%) is integrated 
into the device. The power supply has integrated protection against reverse polarity and surge current 
protection (1.2 A). 
 

Installation 

 

All connections and cables must be laid so as to prevent inductive and capacitive interference 
causing any damage to the device. 

 

Ensure that the infeed lines provide adequate current and voltage carrying capacity. 

 

 

Содержание B-PRIMIS DC-PRIME DC2110W X CM














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды