background image

3 | COMMISSIONING AND MAINTENANCE

23

– let the device run for 6 hours
– deactivate the unit with the remote control

– position the system's main switch in the "OFF" position.

3.5

Ordinary maintenance

Routine maintenance is fundamental for keeping the equipment

efficient, safe and reliable. It can be performed periodically by the

Technical Support Service, whose staff is technically qualified and can

use genuine spare parts, if necessary.

Original conditions must be restored after performing the required

maintenance operations.

All described operations MUST be carried out under the following

conditions:

– cold device
– device NOT supplied with electric power
– suitable personal protection equipment

Do not open the access covers and carry out technical or cleaning

activities before disconnecting the unit from the power grid by

positioning the system's main switch in the "OFF" position

Monthly operations

The following checks are part of the monthly maintenance plan:

– cleaning the housing and front panel
– mesh filter cleaning

cleaning the housing and front panel

– wet a sponge or soft cloth with water and soap to wash
– once cleaning is over dry surfaces with care

Do not use water at a temperature that is higher than 40°C,

powder or abrasive detergents, solvents and brushes.

mesh filter cleaning

1

Mesh filters

– open the front panel

– take out the mesh filter by grabbing the relevant fins
– remove exhausted purifying filters if present
– remove dust with an vacuum cleaner

Stubborn dirt can be removed by washing the filter in a luke warm

(max. 40°C) solution of water and neutral detergent. After

washing, rinse the filters well and leave to dry in the shade.

Exposing the filters to the sun or washing them with water at a

temperature that is higher than 40 °C can cause the filters to

shrink.

It is forbidden to use the device without mesh filter.

Yearly operations

The annual maintenance plan includes the following checks:

– power supply voltage
– electric connection tightening
– status of cooling and hydraulic joint
– condensate tray cleaning
– electric absorption

Purifying filter replacement

To replace the filters:

1

Mesh filters

– open the front panel
– take out the mesh filter by grabbing the relevant fins

1

Mesh filters

2

Air purifying filter

– remove exhausted purifying filters
– insert new purifying filters into the prearranged slots

Содержание 20171580


























Отзывы: