manualshive.com logo in svg

Bercomac 700501-2, Руководство пользователя, Страница: 16 / 28

Поделиться
Скачать
Bercomac 700501-2 Скачать руководство пользователя страница 16

14 

TROUBLESHOOTING 

PROBLEM 

POSSIBLE CAUSES 

CORRECTIVE ACTION 

Winch runs backwards. 

Winch wires reversed. 

Recheck wiring. 

 

Switch wires reversed. 

Recheck wiring. 

 

Switch installed incorrectly. 

Check switch installation. 

 

Battery wires reversed. 

Recheck wiring. 

 

Winch cable is not winded up from 
the bottom of spool. 

Wind winch cable from underneath. 

Winch will not operate or runs in 
one direction only. 

Vehicle’s ignition switch is at OFF 
position. 

Turn vehicle’s ignition switch at ON 
position. 

 

Broken wires or bad connection. 

Check for poor connections. 

 

Control switch is inoperative. 

Replace control switch. 

 

Relay or breaker is damaged.  

Replace the relay or breaker. 

 

Limit switch is damaged. 

Replace limit switch. 

 

Winch is damaged.  

Replace or repair winch. 

Winch runs but with insufficient 
power or line speed. 

Weak battery. 

Recharge or replace battery. 

 

Check charging system 

 

Poor battery connection. 

Check battery terminals for 
corrosion. Clean when required. 

 

Winch is damaged. 

Replace or repair winch. 

* Please refer to parts breakdown section for parts identification

. 

HOW TO KNOW 

POINTS TO CHECK 

Poor connections. 

Recheck wiring with the owner's manual 

HI/LOW voltage tester does not work. 

Connect it on battery posts (+ and -) of a functional battery. 

The 

control 

switch 

inoperative. 

Test both connectors with HI/LOW voltage tester. 
If light comes ON in both positions (IN & OUT), the switch is 
operative. 

Relay is damaged  

When it is working, there is a "CLICK" sound when the control switch 
is activated. Check connections with HI/LOW voltage tester. 

Winch is damaged  

The ultimate test is to connect the winch directly to the battery and 
reverse the wires to test both directions. If the winch doesn't work, it is 
damaged. 

The limit switch is damaged.  

When the limit switch is pushed or stuck inside, the winch can't raise 
the accessory, only lower it. If not replace it. 

The breaker is damaged. 

Check the voltage on both terminals on the breaker with the HI / LOW 
voltage tester. If not replace. 

Содержание 700501-2





























Отзывы:

Нет отзывов