Berchtold CHROMOPHARE F 300 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 67

Berchtold CHROMOPHARE F 300 Скачать руководство пользователя страница 25

The packaging is intended to protect individual components from transport
damage, corrosion and other damage until installation is complete. Therefore,
do not destroy the packaging and remove it only immediately prior to installa-
tion.

Dispose of packaging materials in accordance with legal regulations and local
ordinances.

CAUTION

Incorrect disposal presents an environment hazard

Packaging is made of valuable raw materials. In many cases, additional
uses for the materials are possible, or they can be appropriately recycled
for further use.

ü

Therefore:

1. Dispose of packaging in an environmentally safe manner.
2. Follow local disposal ordinances. If necessary, hire a professio-

nal disposal service.

4.5 Transport

Boxes on pallets can be moved using a forklift provided that:

¡

The construction of the forklift truck must be appropriate to the weight of the
units for transport

¡

The driver must be authorised to drive the forklift truck.

Loading onto the forklift:
1. Drive the forklift truck forward, positioning the forks between or beneath the

pallet rails.

2. Drive forward until the forks protrude from the opposite side.
3. If the centre of gravity is off-centre, make sure the pallet cannot tip over.

Working with packaging
materials

Transporting pallets with
a forklift

Fig. 8: Transport

Examination light CHROMOPHARE F 300

Transport, packaging and storage

25

«
...
23
24
25
26
27
...
»

Содержание CHROMOPHARE F 300




































































Отзывы:

Нет отзывов