manualshive.com logo in svg

Bentek Solar 1000V BUSS Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Bentek Solar 1000V BUSS Series Скачать руководство пользователя страница 41

Installation and Operating Instructions - 1000V BUSS, Grounded (125A to 400A)

950-003342-000 Rev B

41

Chapter 3: Installation Procedure

Connecting the Power for the Fan and Heater

If the Bentek Zone Monitoring System is not included in the product, AC power 

must be connected for the fan and the optional heater.

The fan and optional heater include a power supply that requires external 

voltage to operate. A separate external disconnecting means must be used for 

the incoming power to the power supply. The input voltage of the power supply 

is 104-120VAC at <15A. 

External Disconnect (USA): The external disconnect for the AC power per the 

National Electrical Code must comply with the following requirements: (1) An 

alternating current (AC) disconnecting means shall be mounted within sight of 

or in the equipment. (2) The alternating current (AC) switch shall be located 

where readily accessible and shall be labeled.

External Disconnect (Canada): The external disconnect for the AC power must be 

provided at the time of installation. Check with the installer or contractor for the 

instructions on the external disconnect.

A knockout on the right side of the electronics enclosure provides a 0.875-inch 

hole to accommodate a 0.5-inch conduit. Install the AC power wires through this 

opening.

For the fan, connect 104-120VAC to TB1. Connect AC hot to CB101-1, neutral to 

TB1-N, and ground to TB1-GND using 18-12AWG wire. Wires should either be 

1000V rated or separated from all PV conductors with a barrier.

Figure 21 

Inside of electronics enclosure for fan

For the fan and heater, connect 104-120VAC to TB1. Connect AC hot to CB100-1, 

neutral to TB1-N, and ground to TB1-GND using 18-12AWG wire. Wires should 

either be 1000V rated or separated from all PV conductors with a barrier.

AC power connectors

Содержание 1000V BUSS Series























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды