background image

                                                                                   

Last revised:    May 17, 2013                                                                                                                               

3.4 Zep Components 

 

ZE

ZE

ZE

ZEP GROOVE AND ROCKIT

P GROOVE AND ROCKIT

P GROOVE AND ROCKIT

P GROOVE AND ROCKIT    

The Rockit is a hardware feature which used to secure PV modules to the roof attachments. 

The Rockit fits into the Zep Groove on both sides: The Key side insets, while the Tongue 

side receives. 

 

 

Figure 

Figure 

Figure 

Figure 3

33

3----5

55

5: Zep Groove and Rockit

: Zep Groove and Rockit

: Zep Groove and Rockit

: Zep Groove and Rockit    

 

KEY AND TONGUE

KEY AND TONGUE

KEY AND TONGUE

KEY AND TONGUE    

The Key and Tongue concept informs all Zep Compatible designs. The Key side inserts into 

the Zep Groove, similar to inserting a key into a lock. On the other side, the Zep Groove 

allows PV modules to “drop in” easily onto the Tongue side. 

 

 

Figure 

Figure 

Figure 

Figure 3

33

3----6

66

6: Module Drop

: Module Drop

: Module Drop

: Module Drop----In Example

In Example

In Example

In Example    

 

 

Содержание PM245P01 Series























Отзывы: