BenQ MX507P Скачать руководство пользователя

Страница: 52 / 57

Troubleshooting

The projector does not turn on.

No picture

Blurred image

Remote control does not work

The password is incorrect

Cause

Remedy

There is no power from the power cord.

Plug the power cord into the AC power jack on
the projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.

Attempting to turn the projector on again
during the cooling process.

Wait until the cooling down process has
completed.

Cause

Remedy

The source is not turned on or
connected correctly.

Turn the source on and check that the signal cable
is connected correctly.

The projector is not correctly connected
to the input signal device.

Check the connection.

The input signal has not been correctly
selected.

Select the correct input signal with the

SOURCE

key on the projector or remote control.

The lens cover is still closed.

Open the lens cover.

Cause

Remedy

The projection lens is not correctly
focused.

Adjust the focus of the lens using the focus ring.

The projector and the screen are not
aligned properly.

Adjust the projection angle and direction as well
as the height of the projector if necessary.

The lens cover is still closed.

Open the lens cover.

Cause

Remedy

The battery is out of power.

Replace the battery with new ones.

There is an obstacle between the remote
control and the projector.

Remove the obstacle.

You are too far away from the projector.

Stand within 8 meters (26 feet) of the projector.

Cause

Remedy

You do not remember the password.

Please see

"Entering the password recall

procedure" on page 22

for details.

Содержание MX507P


























































Результаты поиска

Содержание MX507P

Отзывы:

Похожие инструкции для MX507P

Бренды по названию

Популярные бренды

BenQ MX507P, Руководство пользователя

Результаты поиска

Содержание MX507P

Отзывы:

Похожие инструкции для MX507P

Бренды по названию

Популярные бренды