Bennett 1K Series, Быстрая установка

Страница: 9 / 20

9 135442 Rev A 9-18-17
Use the table below to determine how many wires your communication console requires and the connection points for this type of
communication. Note: Connections will vary depending on the dispenser model and options.
1-SIDED DISPENSER COMMUNICATION = 2 FIELD WIRES (REQUIRED)
QTY Description To Board To Connector
1 Orange #18 Wire – Bennett Current Loop Communication (+positive) Current Loop Personality Module TS1, Terminal 1
1 Yellow #18 Wire - Bennett Current Loop Communication (-negative) Current Loop Personality Module TS1, Terminal 2
2-SIDED DISPENSER COMMUNICATION = 4 FIELD WIRES (REQUIRED)
QTY Description To Board To Connector
1 Orange #18 Wire –Bennett Current Loop Communication (+positive) Current Loop Personality Module TS1, Terminal 1
1 Yellow #18 Wire - Bennett Current Loop Communication (-negative) Current Loop Personality Module TS1, Terminal 2
1 Orange #18 Wire –Bennett Current Loop Communication (+positive) Current Loop Personality Module TS2, Terminal 1
1 Yellow #18 Wire - Bennett Current Loop Communication (-negative) Current Loop Personality Module TS2, Terminal 2
GENERIC CURRENT LOOP FUEL COMMUNICATION ( 121982)
To be used with Gilbarco Passport, VeriFone Commander, Wayne Fusion, and Wayne Nucleus remote consoles. Generic Current Loop uses a 2-wire
protocol. Note: Refer to the wiring diagram included in the dispenser for wire, shunts, and field jumper wire connections.
Use the table below to determine how many wires your communication console requires for this type of communication. Note: Connections will
vary depending on the dispenser model and options.
1-SIDED DISPENSER COMMUNICATION = 2 FIELD WIRES AND 1 SHUNT (REQUIRED)
QTY Description To Board To Connector
1 Orange #18 Wire - RS485 Communication (+positive) Current Loop Personality Module TS1, Terminal 1
1 Yellow #18 Wire - RS485 Communication (-negative) Current Loop Personality Module TS1, Terminal 2
1 Shunt Current Loop Personality Module Top 2 Pins at JP1
2-SIDED DISPENSER COMMUNICATION = 2 FIELD WIRES, 1 FIELD JUMPER, AND 2 SHUNTS (REQUIRED)
QTY Description To Board To Connector
1 Orange #18 Wire - RS485 Communication (+positive) Current Loop Personality Module TS1, Terminal 1
1 Field Jumper Wire Current Loop Personality Module TS1, Terminal 2 to TS2, Terminal 1
1 Yellow #18 Wire - RS485 Communication (-negative) Current Loop Personality Module TS2, Terminal 2
2 Shunt (All POS systems except Excentus) Current Loop Personality Module Top 2 Pins at JP1 and JP2
2 Shunt (Use only if an Excentus POS system is used) Current Loop Personality Module Bottom 2 pins at JP1 and JP2
RS-485 FUEL COMMUNICATI ON (121992)
To be used with Allied NeXGen remote consoles. The RS485 uses a 2-wire protocol. RS-485 wires should be twisted together no less than 3 turns
per foot to reduce the effects of electrical noise on the communication circuit. Bennett highly recommends the use of twisted wires. Note: Belden
shielded cable is accepted but the “drain” must not be terminated.
COMMUNICATION = 2 FIELD WIRES
QTY Description To Board To Connector
1 Orange #18 Wire - RS485 Communication (+positive) RS485 Personality Module TS1, Terminal 1
1 Brown #18 Wire - RS485 Communication (-negative) RS485 Personality Module TS1, Terminal 3
CARD READER COMMUNICATION (OPTIONAL)
Bennett Dispensers can interface with many POS terminals as well as site controllers. Refer to the sections below to determine what type of
communication is used and what fueling controller is needed for communication.
Field installed communication wires located inside the electrical enclosure of the unit cannot be loose and must be tightly held in place by
fasteners. RS485 wires should be twisted together no less than 3 turns per foot to reduce the effects of electrical noise on the communication
circuit. Due to the risk of noise causing possible problems with communication, Bennett highly recommends the use of twisted wires. Note: Belden
shielded cable is accepted but the “drain” must not be terminated.
QTY Description To Board To Connector
1 Violet #18 Wire - RS485 Communication (+positive) CPU Board TS1, Terminal 1
1 Yellow #18 Wire - RS485 Communication (-negative) CPU Board TS1, Terminal 3
CARD READER COMMUNICATION
RS485
Ethernet 2-Wire – *COMING SOON*
CAT5e – *COMING SOON*