background image

 

RJW Series of Rolling Jacks 

4

 

P/N 5900093 — Rev. B — October 2020 

You may also contact BendPak for parts replacement information (please have the model and serial 

number of your unit available) at 

(800) 253-2363

, extension 191. 

Shipping Information 

Your unit was carefully checked before shipping. Nevertheless, you should thoroughly inspect the 

shipment before you sign to acknowledge that you received it. 
When you sign the bill of lading, it tells the carrier that the items on the invoice were received in good 

condition. To protect yourself, do not sign the bill of lading until after you have inspected the shipment. 

If any of the items listed on the bill of lading are missing or are damaged, do not accept the shipment 

until the carrier makes a notation on the bill of lading that lists the missing and/or damaged goods. 
If you discover missing or damaged goods after you receive the shipment and have signed the bill of 

lading, notify the carrier at once and request the carrier to make an inspection. If the carrier will not 

make an inspection, prepare a signed statement to the effect that you have notified the carrier (on a 

specific date) and that the carrier has failed to comply with your request. 
It is difficult to collect for loss or damage after you have given the carrier a signed bill of lading. If this 

happens to you, file a claim with the carrier promptly. Support your claim with copies of the bill of 

lading, freight bill, invoice, and photographs, if available. Our willingness to assist in helping you 

process your claim does not make us responsible for collection of claims or replacement of lost or 
damaged materials. 

Safety Considerations 

Read this manual carefully before using your new product.

 Do not set up or operate 

the product until you are familiar with all operating instructions and warnings. Do not allow anyone else 

to operate the product until they are also familiar with all operating instructions and warnings. 

Rolling Bridge Jack Safety Information 

Please note the following: 

 

The product is a Rolling Bridge Jack. 

Use it only for its intended purpose

 

The product must only be operated by authorized, trained personnel. 

 

When the product is in use, keep all body parts away from it. 

 

Do not make any modifications to the product. 

 

WARNING

 

When the Rolling Bridge Jack is on a raised Lift, 

do not go under it

! If you notice 

a Roller out of position, get everyone out from under the Lift, carefully lower the Lift, 

reposition the Rollers back onto the Utility Rail, and then make sure the Safety 
Brackets and Adjustment Bolts are correctly installed and adjusted. 

 

Make sure all operators read and understand this 

Installation and Operation Manual

. Keep the 

manual near the device at all times. 

 

Make a visual inspection of the product before using it every time. Check for missing or damaged 

parts. Do not use the product if you find any of these issues. Instead, take the Jack out of service, 

then contact an authorized repair facility, your distributor, or BendPak at 

(800) 253-2363

Содержание RJ45LP













































Отзывы: