manualshive.com logo in svg

Bender LINETRAXX RCMS150, Руководство пользователя

Поделиться
Скачать
Bender LINETRAXX RCMS150 Скачать руководство пользователя страница 43

Technical data

43

RCMS150_D00259_01_M_XXEN/08.2021

8.  Technical data

(  )* = factory settings

8.1 Tabular data

Insulation coordination according to IEC 60664-1

The data are valid for the monitored primary circuit to the output circuit
Primary circuit..............................................................................Primary conductors routed through the current transformer
Output circuit ..............................................................................................................................................................(+, -, A, B)
Rated insulation voltage......................................................................................................................................................300 V
Overvoltage category................................................................................................................................................................. III
Rated impulse withstand voltage monitored circuit/output circuit .................................................................................... 4 kV
Range of use....................................................................................................................................... ≤ 2000 m above sea level
Rated insulation voltage......................................................................................................................................................250 V
Pollution degree.......................................................................................................................................................................... 3
Insulation 

To achieve double insulation (DI) for overvoltage category III, insulated primary conductors with sufficient rated
voltage must be used on the application side.
BI............................................................................................................................................ Overvoltage category III
DI............................................................................................................................................. Overvoltage category II

Voltage test acc. to IEC 61010-1 .................................................................................................................................. AC 2.2 kV

Power supply

Nominal supply voltage 

U

S

 ............................................................................................................................................. DC 24 V

Operating range 

U

S

...........................................................................................................................................................±20 %

Power consumption .........................................................................................................................................................  < 4 W

Residual current measuring range

Frequency range  .....................................................................................................................................................0…2000 Hz
Measuring range ..........................................................................................................................................................±500 mA
Resolution measured value ..........................................................................................................1 % of the set response value

Response values

Residual current 

I

Δn2 RMS

 ...............................................................................................................RMS 3…300 mA (30 mA)*

Residual current 

I

Δn2 DC

 .......................................................................................................................DC 3…300 mA (6 mA)*

Ratio 

I

Δn2 RMS

 / 

I

Δn2 DC

 .................................................................................................................................................... 0.2…5

Prewarning 

I

Δn1 RMS/DC

 ................................................................................................................. 50…100 % of 

I

Δn2 

(50 %)*

Содержание LINETRAXX RCMS150





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды