Benchmark AHB2 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 41

Benchmark AHB2 Скачать руководство пользователя страница 13

AHB2

Instruction Manual Rev F

Page 13

Rack Mounting

The

AHB2

is available in a rack-mount version. The

AHB2

is magnetically shielded, and will not

interfere with sensitive equipment mounted above or below the

AHB2

.

Rack Mount Option

Rack Mounting Instructions

The

AHB2

runs very cool when idle and runs very cool under most load conditions. However, it can

produce significant heat when heavily loaded. Make sure the rack is adequately ventilated. Make

sure the side heat sinks have an unobstructed air flow.

Some power amplifiers can emit very strong magnetic fields. These amplifiers should be kept at
least two rack units above or below the

AHB2

. Magnetic interference can produce hum problems.

If the

AHB2

is mounted directly above another piece of equipment, it may be necessary to remove

the feet from the

AHB2

. Save the feet for future needs. Replacement feet may be purchased

directly from Benchmark or through most authorized Benchmark dealers.

«
...
11
12
13
14
15
...
»

Содержание AHB2










































Отзывы:

Нет отзывов