S.p.A.
F 1900
4
PACKING AND TRANSPORT
◊
WIDTH: 100 cm
◊
DEPTH: 47 cm
◊
HEIGHT: 63 cm
⇒
Remove the pow er mow er from its packing.
⇒
⇒
⇒
⇒
Fix the handles to the handlebar support using the tw o screw s and tw o knobs pre-mounted on the handle.
Make sure to position the control cables correctly .
⇒
⇒
⇒
⇒
Fix the bar to the machine, by unspitting the spring (Picture 9 Ref. A) on the pin Ref. B. Thread the pin in the casing
Ref. C and thread the spring again (Ref. A). Take the little plastic cy linder (Picture 9 Ref. D), threat it in the grass
divider head Ref. E and threat all in the pin of the lever arm Ref. F, in the holes on the head and on the cy linder. Fix
the head Ref. E to the bar by screw ing tw o screw s Ref. G in the threaded holes on the bar.
⇒
⇒
⇒
⇒
If the machine is to be transported, empty out the petrol tank and alw ay s apply the plastic protective strip to
the cutting bar blade. If E.S.M. ty pe, please read the sheet enclosed.
IMPORTANT: THE PACKED MACHINE IS SUPPLIED WITH THE MOTOR WITHOUT OIL OR PETROL.
SAFETY RULES
•
Read carefully the operation and maintenance manual enclosed w ith the machine.
•
The use of the machine is prohibited to persons under 16 y ears of age.
•
The operator is liable for damages since the machine is under his control.
•
Those unfamiliar w ith the machine or w ho have never used it are obliged to read the operation and
maintenance manual before operation.
•
In case of transport, disassemble the bar and empty the petrol out of the tank.
•
If the machine is left unattended, ensure that it cannot start up again.
•
Before running the machine, the operator must have a 5 meter radius of free space around him.
•
Dry any petrol leaks.
•
Fill up the tank w ith the motor off. Filling the tank or transferring fuel must alw ay s be performed outdoors, aw ay
from flames or heat sources. Do not smoke during this operation.
•
W hen mow ing in mountainous areas or on slopes, mow horizontally and use non-skid equipment on shoes and
w heels.
•
If the blade needs replacement, observe E.S.M. operation and maintenance procedures.
•
If the bar suffers impact, check the condition of the bar before resuming w ork.
•
Keep feet and hands far aw ay from the cutting bar and all rotating parts.
•
Do not run the motor w here ex haust containing carbon monox ide may accumulate.
•
Never use the mow er incomplete or w ithout its safety device.
•
Do not assemble/disassemble or clean the cutting bar or other equipment w ith the motor running.
•
Caution! W hen the clutch is engaged the cutting bar is alw ay s in motion.
•
Caution! Do not mow areas w ith slopes ex ceeding 50%.
•
W e w ill not be held liable for accidents caused by the failure to observe these rules.
STARTING AND STOPPING THE POWER MOWER
Every time y ou get ready to start the motor, make a careful check of the follow ing:
•
Make sure that fuel is in the tank.
•
Check the motor oil level: CAU TION: MACHINES OU T OF THE FACTORY DO NOT CONTAIN OIL IN THE MOTOR.
Make sure to add oil up to the level on the dipstick.
•
CONSU LT THE OPERATION AND MAINTENANCE MANU AL OF THE MOTOR U NDER "BEFORE START-U P"
•
Make sure oil is up to the level in the gearbox (Picture 5 Ref. A)
•
Check that all safety sy stems are released and functioning, especially the levers Ref. B and Ref. C Picture 6
•
Press the "Primer" button three times in case of starting w ith the motor cold (Picture 1 Ref. 11) only version B&S.
•
Alw ay s start the motor up outdoors.
•
Bring the accelerator hand lever (Picture 6 Ref. "A”) to the "START" position, grasp the cord handle (Picture 7) and
pull it slightly until y ou feel some resistance, then pull harder. Make sure that the cord does not return by itself --
accompany it w ith y our hand.
