BeLuce STELLA SD Скачать руководство пользователя страница 1

Страница: 1 / 26

BeLuce Canada Inc., 3900 14th Avenue, Unit 1, Markham, ON L3R 4R3 P: (905) 948-9500 F: (905) 948-8673

INSTALLATION

Hardwired Installation:

1. Extend unswitched 24 hour AC supply of rated voltage to a junction box (supplied by others) installed in

accordance with all applicable codes and standards. Leave at least 8 inches of slack wire. This circuit should NOT

be energized/live at this time.

2. Open the unit by unscrewing the cover screws on the sides of the unit (Figure 1). The front cover can then be lifted

up and removed.

3. Unit is supplied with universal spider knockouts and keyhole slots stamped into the back of the cabinet. Knock out

the appropriate hole(s) and bring wires through the hole(s) into the cabinet.

4. Mount the unit securely into place. Do not rely on the electrical box as the only support for the unit. There are two

keyhole mounting slots provided in the back of the unit for wall mounting.

5. Make proper wiring connections between the AC supply and the unit’s transformer per diagram provided (Figure 4).

Insulate unused wire!

Connect ground to supplied green ground wire in accordance with local codes.

Reassemble all wire connections and connectors.

CAUTION! - Failure to insulate unused wire may result in a

shock hazard or unsafe condition as well as equipment failure.

6. For large units the batteries may be shipped separately. Install batteries into the cabinet and complete the

appropriate battery connections (Figure 5).

7. Uncoil the wire lead(s) from the Positive circuit board terminal (+) and connect to the positive terminal connector on the

battery (Figure 2).

8. Route wires and secure in place.

9. Replace cover and secure cover screws.

10. Turn on AC line voltage supply.

11. Position lamps/heads to provide best lighting distribution by loosening head set screws to adjust angle and swivel.

Manually rotate or twist head to desired position then tighten set screws to lock position.

INSTRUCTIONS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS

2. For Indoor use ONLY.

3. Do not let the power cords touch hot surfaces.

4. Do not install near gas or electric heaters.

5. Use caution when servicing batteries. Battery acid can cause burns to the skin and eyes. If acid is spilled on skin or eyes, flush acid with

fresh water and contact a physician immediately.

6. The equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to tampering.

7. The use of accessory equipment not recommended by the manufacturer, may cause an unsafe condition, and will void the unit’s

warranty.

8. Do not use this equipment for other than its intended purpose.

9. Servicing of this equipment should be performed by qualified service personnel.

10. SAVE THESE INSTRUCTIONS!

STELLA SD (SL-SD)

926000535

OPERATION

ACDC models:

1. Sign will illuminate when supplied with power.

CAUTION

This equipment is furnished with a sophisticated low voltage battery dropout circuit to protect the battery from over-discharge

after it’s useful output has been used. Allow 24 hours recharge time after installation or power failure for full-load testing.

Содержание STELLA SD



























Результаты поиска

Содержание STELLA SD

Отзывы:

Похожие инструкции для STELLA SD

Бренды по названию

Популярные бренды

BeLuce STELLA SD, Инструкция по эксплуатации

Результаты поиска

Содержание STELLA SD

Отзывы:

Похожие инструкции для STELLA SD

Бренды по названию

Популярные бренды