10
11
Overview of Programming Options
Press the REV button
to go from one category
to the next
PILOT LIGHT
(Power-on indication)
POWER-ON SEQUENCE
SIGNAL STRENGTH METER
AUTOMUTE
VOICE**
CITY MODE SENSITIVITY
BRIGHTNESS
BANDS
*
RX75’s Factory Default Settings
To reset RX75 to its original factory
settings, press and hold the “CITY”
and “VOL/MUTE” buttons while
turning the power on. The RX75’s
display will provide a “Reset”
message, accompanied by an
audible alert, acknowledging the
reset.
**
Available only with Optional Speaker
Pilot HWY
Pilot H
Pilot V
PwrOn STD
PwrOn FST
Meter STD
Meter THT
Meter TEC
aMute ON
aMute OFF
Voice On
Voice Off
City STD
City LoX
City NoX
Brt AUTO
Brt MIN
Brt MED
Brt MAX
Brt DARK
Bands ALL
Bands MOD
X
ON
or
OFF
K
ON
or
OFF
Ka
ON
or
OFF
LSR ON
or
OFF (
or
BLCK
with optional LP904)
SWS ON
or
OFF
Press the CHANGE button
to change your setting
within a category
*
Full word: Highway or Auto or City
Letter: H or A or C
Vehicle voltage
*
Standard power-on sequence
Fast power-on sequence
*
Standard signal strength meter
Threat Display
™
TechDisplay
*
AutoMute on
AutoMute off
*
Voice on
Voice off
*
Standard City mode sensitivity
Low X-band sensitivity in City Mode
No X-band sensitivity in City Mode
*
Brightness adjusts automatically
Minimum brightness
Medium brightness
Maximum brightness
Dark Mode
*
All bands enabled
One or more bands has been modified
Turn bands “ON” or “OFF” by holding
down the VOL/MUTE button
Details of Programming Options
Pilot Light (Power-on indication)
Note: When you are using the Dark mode,
the display will only show HD, AD, or CD,
(Highway-Dark, AutoScan-Dark, or City-
Dark).
PilotHWY
(Full description)
In this setting, the RX75 will display
“Highway,” “City,” or “AutoScan” as its
power-on indication. (factory default)
Pilot H
(Letter)
In this setting, the RX75 will display “H” for
Highway, “C” for City, or “A” for AutoScan.
Pilot V
(Vehicle voltage)
In this setting, the RX75 will display “H” for
Highway, “C” for City, and “A” for Auto, and
the vehicle’s voltage. If the vehicle’s voltage
drops below 10.5 volts, a low voltage
warning will be displayed, followed by an
audible alert. A high voltage warning is also
given when the vehicle’s voltage goes
above 16.5 volts.
Power-on Sequence
PwrOnSTD
(Standard)
In this setting, each time you turn on the
RX75, it will display “BEL PRO,” “RX75,”
“LASER,” “Ka-band,” “K-band,” “X-band,”
followed by a brief X-band alert. It then
confirms communications to all of its
components. If a communications error
occurs, the appropriate error message will
be displayed. (see page 21 for error messages)
Note: If there is a problem with the front
laser receiver or wiring after the initial
start-up sequence, the RX75 will briefly
display “LsrF ERR.” If there is a problem
with the rear laser receiver or wiring after
the initial start-up sequence, the RX75 will
briefly display “LsrR N/A.”
In both cases, the RX75 will continue
to receive radar signals, but will not
receive laser signals. If there is a problem
with the front radar receiver or wiring
after the initial start-up sequence, the
RX75 will display “Front N/A,” and will
then continue to display “Check,”
“Receiver,” “Wiring.” The RX75 will not
operate in this condition. Please contact
your installer if this occurs.
PwrOnFST
(Fast power-on)
This setting shortens RX75’s start up
sequence to single beep, eliminating the
words “BEL PRO,” “RX75,” “LASER,”
“Ka-band,” “K-band,” “X-band,” from the
start-up sequence.
