background image

12

13

Changing the radio key

If your Visit system is activated for no reason, there is probably a nearby system that triggers 

yours. In order to avoid radio interference, you need to change the radio key on 

all

 units.

Systems with 

different types

 of transmitters

Change the radio key on all 

other

 transmitters in the system by moving any of the radio key 

switches, see the corresponding transmitter user manual.

Changing the radio key on the BE1555 CO alarm
1

  Remove the alarm from the bracket to access the radio button, see

 Overview

. Press and 

hold the radio button until the radio LED blinks slowly in blue. Release the button.

2

  Press the test button on any 

other

 transmitter within 30 s to transmit the new radio key.

3

  The radio LED on the alarm lights up in blue to show that the radio key has been changed. 

1

2

3

RADIO

ALARM

FAULT

POWER

TEST

&

HUSH

CARBON

MONOXIDE

ALARM

Changing the radio key on a receiver
1

  Press and hold the test/function button on the Visit receiver until the green and yellow LEDs 

blink alternately, see image on the next page. Release the button.

2

  Within 30 s, press the test/hush button and release it when the alarm sounds to transmit the 

new radio key. 

3

  All LEDs on the receiver blink 5 times to show that the radio key has been changed.

RADIO

ALARM

FAULT

POWER

TEST

&

PUSH

CARBON

MONOXIDE

ALARM

RADIO

ALARM

FAULT

POWER

TEST

&

PUSH

CARBON

MONOXIDE

ALARM

Systems with

 only

 BE1555 CO alarms

Changing the radio key on the CO alarms

Select one of the BE1555 CO alarms that will function as the 

master

 unit. The other alarms will 

function as 

slave

 units. Remove the CO alarms from the brackets to access the radio button.

1

  Press and hold the radio button on the 

master

 unit until the radio LED blinks slowly in blue. Press 

and hold the button again to generate a new radio key. The radio LED will pulsate to confirm. 

2

  Press and hold the radio button on the 

slave

 unit until the radio LED blinks slowly in blue. 

3

  Press the test/hush button on the 

master

 unit and realese it when the alarm sounds to 

transmit the new radio key. 

4

  The radio LED on the 

slave

 unit lights up in blue to show that the radio key has been changed. 

Repeat steps 2 – 4 to change the radio key on an additional BE1555 CO alarm.

Changing the radio key on a receiver
1

  Press and hold the test/function button on the Visit receiver until the green and yellow LEDs 

blink alternately, see image on the next page. Release the button.

2

  Within 30 s, press the test/hush button and release it when the alarm sounds to transmit the 

new radio key. 

3

  All LEDs on the receiver blink 5 times to show that the radio key has been changed.

5

1

2

3

RADIO

ALARM

FAULT

POWER

TEST

&

PUSH

CARBON

MONOXIDE

ALARM

EN

Содержание BE1555
















Отзывы: