manualshive.com logo in svg

Bell UPC, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Bell UPC Скачать руководство пользователя страница 22

22

193558045 - v.6  UPD 310117

7 - MAINTENANCE

The routine maintenance work described below must be performed exclusively by a skilled technician who has a thorough knowledge of 
the pump and its operation and who has read this manual completely. Maintenance must be carried out with maximum caution to prevent 
possible accidents. This chapter describes the only maintenance procedures permitted. 

Execution of any unauthorised maintenance 

work will automatically invalidate the warranty and free the manufacturer from all liability.

BEFORE ANY OPERATION OF MAINTENANCE THE PUMP MUST BE DISCONNECTED FROM THE PNEU-
MATIC CIRCUIT.  THEN UNLOAD THE OIL PRESSURE IN THE HYDRAULIC CIRCUIT.

7.1 - Checking connections

Periodically check the hydraulic and pneumatic connections. Ensure that the connections on the pump are screwed down tightly and 
show no signs of breakage, cracks or other damage. Ensure that the hoses are not damaged in any way (cuts, abrasion, cracks, etc.).
If you use the pump in an intensive manner, we suggest a weekly check.

7.2 - Cleaning the air fi lter

Periodically clean the air 

fi

 lter.

If you use the pump in an intensive manner, we suggest a weekly check.
The air 

fi

 lter is inside the inlet pneumatic 

fi

 tting (

fi

 g.10, page 5).

 

●

Use a slotted tip screwdriver of the appropriate size to unscrew the 

fi

 lter from the air inlet connection until it is extracted.

 

●

Clean the 

fi

 lter with compressed air and then re

fi

 t and screw it into position. Do not over-tighten the 

fi

 lter or damage may ensue.

 

●

Reconnect the air line quick coupler after binding the thread with Te

fl

 on tape.

If the air 

fi

 lter is excessively contaminated or damaged, it must be renewed. Order a new 

fi

 lter from the manufacturer, referring to the list 

of spare parts at the end of this manual.

6.3 - Priming of the pump

WARNING

IMMEDIATELY AFTER THE PUMP INSTALLATION, THE CIRCUIT MAY CONTAIN AIR LOCKS WHICH PRE-
VENT PRESSURIZATION. IF THE PUMP IS UNABLE TO PRESSURIZE THE OIL CIRCUIT, PROCEED AS 
DESCRIBED BELOW.

THE OPERATIONS DESCRIBED BELOW MAY BE PERFORMED ON THE PEDAL USING THE HANDS, SOLELY 
IF YOU PRESS ONLY THE APPROPRIATE ZONES INDICATED ON THE PEDAL ITSELF

IF THE PUMP IS MOUNTED VERTICALLY, DISASSEMBLE IT AND PLACE IT IN A HORIZONTAL POSITION 
ON THE FLOOR.

6.3.1 - UPM and UPC models with 4/3 directional control valve

 

●

Press the pump treadle and position the valve (or control lever) on releasing position, i.e. pos.2 (

fi

 g.9/b, page 5) for  about 15 seconds.

 

●

Connect to a cylinder and check that the pump is primed. If the cylinder does not move. Repeat the operation.

6.3.2 - UPL and UPC models with 4/2 directional control valve

 

●

Using a suitable pressure hose, connect the pressurized oil delivery port to the drain side and press the treadle for about 15 seconds.

 

●

Connect to a cylinder and check that the pump is primed. Repeat the operation if the cylinder does not move.

Содержание UPC





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды