Bell BE-70PS Owner's Скачать руководство пользователя страница 2

- 3 - 

IMPORTANT SAFETY INSTRUCTIONS 

When using your telephone equipment, basic safety precautions should always be 
followed to reduce the risk of fire, electrical shock, and injury to persons including 
the following: 

1. Read and understand all instructions. 

2. Follow all warnings and instructions marked on the product. 

3. Unplug this product from the wall outlet before cleaning. Do not use liquid 

cleaners, or aerosol cleaners. Use a damp cloth for cleaning. If necessary, use 
a mild soap. 

4. Do not use this product near water, for example near a bath tub, wash bowl, 

kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 

5. Do not place this product on an unstable cart, stand or table. The product may 

fall, causing serious damage to the product. 

6. This product should be operated only from the type of power source indicated 

on the marking label. If you are not sure of the type of power supply to your 
home, consult your dealer or local power company. 

7. Do not allow anything to rest on the telephone line cord. Do not locate this 

product where the cord will be abused by persons walking on it. 

8. Never push objects of any kind into this product through the cabinet slots as 

they may touch dangerous voltage points or short out parts that could result in 
a risk of fire or electric shock. Never spill liquid of any kind on the product. 

9. To reduce the risk of electric shock, do not disassemble this product, but take 

it to a qualified serviceman when some service or repair work is required. 
Opening or removing covers may expose you to dangerous voltages or other 
risks. Incorrect reassembly can cause electric shock when the appliance is 
subsequently used. 

10. Unplug this product from the wall outlet and refer to qualified service personnel 

under the following conditions: 

a. When the power supply cord or plug is damaged or frayed. 

b. If liquid has been spilled into the product. 

c. If the product has been exposed to rain or water. 

d. If the product does not operate normally by following the operating 

instructions. Adjust only those controls, that are covered by the operating 
instructions because improper adjustment of other controls may result in 
damage and will often require extensive work by a qualified technician to 
restore the product to normal operation. 

e. If the product has been dropped or the cabinet has been damaged. 

f. If the product exhibits a distinct change in performance. 

11. Avoid using a telephone (other than a cordless type) during an electrical storm. 

There may be a remote risk of electrical shock from lightning. 

12. Do not overload wall outlets and extension cords as this can result in the risk 

of fire or electrical shock. 

13. Do not use the telephone to report a gas leak in the vicinity of the leak. 

SAVE THESE INSTRUCTIONS 

Содержание BE-70PS Owner's


























Отзывы: