Belden lumberg automation 934 878-001 Скачать руководство пользователя страница 47

Страница: 47 / 75

7 Diagnostic Properties of the

Modules

7.1 Channel Error

7 Diagnostic Properties of the

Modules

The modules provide advanced diagnosis behavior, in particular for the output

channels to determine errors in the transmission. The firmware of the modules

differentiates between five distinct types of error.

7.1 Channel Error

A channel error is determined by comparing the target value set by a controller

and the actual value of the output channel.

Target value

Actual value

Comment

Active

OK, no diagnosis

Off

OK, no diagnosis

Active

Off

Short circuit, channel indicator

is red. Channel error bit in the

diagnosis is set. Channel is

locked after error is removed.

Off

Active

Voltage fed back in, red and

yellow/white channel indicators

are activated. Channel error bit

in the diagnosis is set.

Table 25: Interpretation of channel errors

Attention:

If both output channels of an M12 slot are activated when

a channel error occurs, the controller locks both channels, even if only

one channel is affected by the error. If only one channel is activated,

the controller only locks this one. Locked channels are deactivated

and remain in the Off state if you do not reset them using the controller.

When an output channel is activated (rising edge of the channel state) or

deactivated (falling edge), the channel errors are filtered for the period that

you set using the "Surveillance Timeout" parameter during the configuration

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Содержание lumberg automation 934 878-001












































































Результаты поиска

Содержание lumberg automation 934 878-001

Отзывы:

Похожие инструкции для lumberg automation 934 878-001

Бренды по названию

Популярные бренды

Belden lumberg automation 934 878-001, Техническое руководство

Результаты поиска

Содержание lumberg automation 934 878-001

Отзывы:

Похожие инструкции для lumberg automation 934 878-001

Бренды по названию

Популярные бренды