background image

 

25/27 

In the phase contrast 
observation, the bottom 
thickness of the culture dish 
is more than 1.2mm. 

 Use a the culture dish 
whose bottom thickness is 
less than 1.2mm 

Use a bright field objective   

Change to the phase contrast 
objective 

12 

The condenser ring is not 
coincident with the objective 
phase ring 

Adjust the condenser ring to 
match the objective phase 
ring 

12 

The light ring and the phase 
contrast kits is not centered 

Adjust the bolts to center 
them 

12 

The objective used is not 
fit to the phase contrast 
observation 

Please use the compatible 
objective 

12 

the phase 
contrast effect 

When looking at the edge of 
the culture dish, the phase 
contrast ring and the light 
ring is deviated each other 

Moving the culture dish 
until you obtain the phase 
contrast effect. You also 
could demount the slider, 
and dail the field diaphragm 
with the direction of    “

 

” 

13 

The nosepiece is not in the 
center of the light path 

Insure the nosepiece is in 
the “clicked” position 

The specimen don’t place 
properly 

 Place the specimen on the 
stage correctly. 

6.one side of the 
image is unfocused  The optical performance of 

the culture dish bottom is 
poor (such as erose figure 
and soon) 

Please use a regular culture 
dish 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание INV100-FL




























Отзывы: