background image

BEL DIGITAL AUDIO   Bel2120B 

 2004 BEL Digital Audio Ltd. 

16

AES I/O 
 Pin 1 Ch1/2 + Out Pin 9 GND 
 Pin 2 Ch1/2 -Out Pin 10 GND 
 Pin 3 Ch3/4 +Out Pin 11 GND 
 Pin 4 Ch3/4 - Out Pin 12 GND 
 Pin 5 Ch1/2 + In Pin 13 GND 
 Pin 6 Ch1/2 - In Pin 14 GND 
 Pin 7 Ch3/4 + In Pin 15 GND 
 Pin 8 Ch3/4 +-In   
RS422 IN 
 Pin 1 Chassis Pin 6 GND 
 Pin 2 Tx -  Pin 7 Tx + 
 Pin 3 Rx +  Pin 8 Rx - 
 Pin 4 GND  Pin 9 Chassis 
 Pin 5 GND   
 
RS422 OUT 
 Pin 1 Chassis Pin 6 GND 
 Pin 2 Rx -  Pin 7 Rx + 
 Pin 3 Tx +  Pin 8 Tx - 
 Pin 4 GND  Pin 9 Chassis 
 Pin 5 GND 
 
 
 It is recommended that, where possible, all cables be good quality screened 
twisted pairs with the screening braid connected to pin 1 on the XLR connector. 
Optimum performance is obtained using double screened cable with separate ground 
returns. It is also recommended that 360 degree connection be made to the screening 
braid on the BNC connectors. Screened ‘D’ type connectors are also recommended. 
 

EMC compliance 

 The BEL 2120 was designed and tested to comply with the EMC directive 
numbers EN55103, EN55022 and EN55082-1 when used as directed. 
 

CE 

 

Содержание 2120B



































Отзывы: