Beko WTV 8744 XDW страница 62 Скачать руководство пользователя

Страница: 62 / 68

EN / 62

Washing Machine / User’s Manual

Problem

Cause

Solution

No water can be

seen in the product

during washing.

Water is inside the invisible

part of the product.

•

This is not a failure.

Loading door cannot

be opened.

Loading door lock is activated

because of the water level in

the product.

•

Drain the water by running the Pump or

Spin programme.

Product is heating up the

water or it is at the spinning

cycle.

•

Wait until the programme completes.

Loading door may be stuck

because of the pressure it is

subjected to.

•

Grab the handle and push and pull the

loading door to release and open it.

If there is no power, loading

door of the product will not

open.

•

To open the loading door, open the pump

filter cap and pull down the emergency

handle positioned at the rear side of the

said cap. See “Opening the loading door in

case of power failure”

Washing takes

longer than

specified in the user

manual.(*)

Water pressure is low.

•

Product waits until taking in adequate

amount of water to prevent poor

washing quality due to the decreased

amount of water. Therefore, the washing

time extends.

Voltage is low.

•

Washing time is prolonged to avoid poor

washing results when the supply voltage

is low.

Input temperature of water

is low.

•

Required time to heat up the water

extends in cold seasons. Also, washing

time can be lengthened to avoid poor

washing results.

Number of rinses and/or

amount of rinse water have

increased.

•

Product increases the amount of rinse

water when good rinsing is needed and

adds an extra rinsing step if necessary.

Excessive foam has occurred

and automatic foam

absorption system has been

activated due to too much

detergent usage.

•

Use recommended amount of detergent.

Programme

time does not

countdown. (On

models with display)

(*)

Timer may stop during water

intake.

•

Timer indicator will not countdown until

the product takes in adequate amount of

water. The product will wait until there is

sufficient amount of water to avoid poor

washing results due to lack of water.

Timer indicator will resume countdown

after this.

Timer may stop during heating

step.

•

Timer indicator will not countdown

until the product reaches the selected

temperature.

Timer may stop during

spinning step.

•

Automatic unbalanced load detection

system is activated due to the

unbalanced distribution of the laundry in

the product.

Содержание WTV 8744 XDW





































































Результаты поиска

Содержание WTV 8744 XDW

Отзывы:

Похожие инструкции для WTV 8744 XDW

Бренды по названию

Популярные бренды

Beko WTV 8744 XDW, Руководство пользователя

Результаты поиска

Содержание WTV 8744 XDW

Отзывы:

Похожие инструкции для WTV 8744 XDW

Бренды по названию

Популярные бренды