Beko WMB 61011 PL N, Руководство пользователя

Страница: 4 / 32

4 / 32 EN
Washing Machine / User’s Manual
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
A
WARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
• The hose should be attached to a height of at least 40 cm,
and 100 cm at most.
• In case the hose is elevated after laying it on the floor level
or close to the ground (less than 40 cm above the ground),
water discharge becomes more difficult and the laundry
may come out excessively wet. Therefore, follow the
heights described in the figure.
• To prevent flowing of dirty water back into the machine and
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between the
drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may not
be longer than 3.2 m. To avoid water leak failures, the
connection between the extension hose and the drain
hose of the product must be fitted well with an appropriate
clamp as not to come off and leak.
2.6 Adjusting the feet
A
WARNING
In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise, the product may
move from its place and cause crushing and vibration problems.
Loosen the lock nuts on the feet by hand. Adjust the feet until
the product stands level and balanced. Tighten all lock nuts
again by hand.
A
WARNING
Do not use any tools to loosen the lock nuts. Otherwise, they will
get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a fuse
complying with the values in the "Technical specifications"
table. Our company shall not be liable for any damages that
will arise when the product is used without grounding in
accordance with the local regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• The voltage and allowed fuse or breaker protection are
specified in the “Technical specifications” section. If the
current value of the fuse or breaker in the house is less
than 16 Amps, have a qualified electrician install a 16 Amp
fuse.
• The specified voltage must be equal to your mains voltage.
• Do not make connections via extension cables or multi-
plugs.
B
WARNING
Damaged power cables must be replaced by the Authorized Service
Agents.
2.8 First use
Before starting to use the product, make sure that all
preparations are made in accordance with the instructions in
sections "Important safety instructions" and "Installation".
To prepare the product for washing laundry, perform first
operation in Cotton-90 programme. Before starting the
programme, put max. 100 g of powder anti-limescale into
the main wash detergent compartment (compartment nr. II).
If the anti-limescale is in tablet form, put only one tablet into
compartment nr. II. Dry the inside of the bellow with a clean
piece of cloth after the programme has come to an end.
C
INFORMATIONS
Use an anti-limescale suitable for the washing machines.
Some water might have remained in the product due to the quality
control processes in the production. It is not harmful for the product.
2.9 Disposing of packaging material
Packaging materials are dangerous to children. Keep
packaging materials in a safe place away from reach of the
children.
Packaging materials of the product are manufactured from
recyclable materials. Dispose of them properly and sort in
accordance with recycled waste instructions. Do not dispose
of them with normal domestic waste.
2.10 Transportation of the product
Unplug the product before transporting it. Remove water drain
and water supply connections. Drain the remaining water in
the product completely; see, "Draining remaining water and
cleaning the pump filter". Install transportation safety bolts in
the reverse order of removal procedure; see, "Removing the
transportation locks".
C
INFORMATIONS
Never move the product without the transportation safety bolts
properly fixed in place!